KINEX EK-BT1-TP Manual
1Advanced IP-KNX interface for KNX and/or Control4installations is a web-server designed to offer a suiteof connectivity and functional services to a Control4supervision system, when used in combination withekinex KNX devices.Technical Sheet STEKBT1TP_EN• 1 Ethernet port via cat. 5 or higher cable and standardRJ45 connector• 1 RS485 port for future integrations• 1 USB 2.0 port: for future integrations• 2 frontal LEDs: POWER LED for signalling the pre-sence of power supply; SERVICE LED for signallingparticular operations in progress• 1 RESET button housed under the front cover on theback of the vertical cardOther features:• Plastic housing• Design for mounting on 35 mm profile rail (accordingto EN 60715)• Degree of protection IP20 with product installed (accor-ding to EN 60529)• Insulation class II (according to EN 60335-1• Climatic classification 3K5 (indoor, dry) and mechanical3M2 (according to EN50491-2)• Device weight: 120 g• 2 UM modular device (1 UM = 18 mm)• Dimensions 36 x 90.5 x 62 mm (W x H x D)Environmental conditions:• Operating temperature: 0°C ... + 40°C• Storage temperature: - 10 ... + 70°C• Transport temperature: - 10 ... + 70°C• Relative humidity: 95% non-condensingOperating, signaling and connection elementsEK-BT1-TP server is equipped with status LEDs, a RE-SET button located under the front panel of the device,terminals for power supply connection, KNX bus line andEthernet network. The server offers also an USB andRS485 port, prepared for future use (not available at thepresent moment in the configuration process).Advanced IP-KNX interface for KNX and/orControl4 installationsDescriptionThe EK-BT1-TP server interface is designed for instal-lation on DIN profile rail and occupies 2 modules. The12-24 Vdc power supply is external (power supply not in-cluded). The product with hardware based on embeddedoperating system, has a KNX TP node (twisted pair) andcan therefore be connected directly to the bus network ofKNX devices. Connectivity as an IP gateway for Control4is via the Ethernet port. The integrated web server builtwith HTML5 technology allows access to the configura-tion environment.With EK-BT1-TP it is possible to:• Send commands and receive information from KNX de-vices in the CONTROL4 system• Monitor the building energy consumption and controlloads accordingly with the overall absorption with a de-dicated graphic driver for Composer• Make a continuous diagnostic check on the KNX de-vices and receive notifications in case of malfunctions• Define command sequences (scenes) and executethem with simple connections in Composer with 3rdparty drivers• Perform logics configurable with a graphic editor andexecuted in background• Send notifications to CONTROL4 in case of malfun-ctions or configurable events on the busMain features• 12-24 Vdc power supply (absorption 240 mA at 12 Vdc)by means of a special plug-in terminal supplied. Powersupply not included• KNX TP bus (twisted pair) via red-black terminal pro-vided6453121. LED SERVICE2. LED POWER3. RESET push-button4. Clamp for power-supply 12-24 Vdc5. Clamp for KNX bus6. RJ45 Ethernet plug7. Clamp for RS485 network8. 2.0 USB portSignaling elements• POWER LED: indicates the presence of 12-24 Vdc po-wer supply at terminals• SERVICE LED: Normally off, steady mode or flashingduring IP address recovery sequences or factory re-configurationsCodes: EK-BT1-TP87 |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine