KITA KP20C Series Manual
  |
Panel adapter PA-2Panel adapter PA-1Front protective lid FPC-1Mou nti ng bracke t BT-1KP-20R KITA SENSOR TECH. CO., LTD.TYPE OF SPARE PARTS / DIMENSION GRAPHUNIT DIM ENSIO N / PANEL IN STRUCTIO NS3 ½ digit LED displaySwitch (OUT1)Setting Button(Green LED)Display the measuredpressure value. each setcontent and error code.( )ButtonChange setting mode andpre-set final desired value.Switch(OUT 2)(Red LED)Use the button to changesetting mode and pre-setdesired value.OUTPUT CIRCUIT WIRING GRAPHKP20This product has two inlet pressure ports,select the one most convenient forinstallation.Please plug the unused inlet port withsupplied port plug. Use seal tape toprevent pressure leak.Bolt(screw)INSTALLATION1.2.Mounting bracketMounting bracketPanel typePanel typeFor your safety, please read the following before using.For your safety, please read the following before using.Do not use corrosive or flammable gas or liquid with this product.Please use within the operating pressure range. Do not apply pressure beyond recommended maximum pressure,permanent damage to the pressure sensor may occur.2Do not drop, hit or allow excessive shock (1000m/s or 100G). Even if switch body appears undamaged, internalcomponents may be broken and can cause malfunction.Turn power off before connecting wiring. Wrong wiring or short circuit will damage and / or cause malfunction.Do not use in environment containing steam or oil vapor.This product is not explosion-proof rated. Do not use in atmosphere containing flammable or explosive gases.Wiring for pressure sensor should avoid power source line and high voltage line. If use in the same circuit, noise maycause malfunction.1234567ORDERING INFORMATIONUse the button to changesetting mode and pre-setdesired value.( )Button1122Mounti ng brac ke t BT-2BT-2PA-2PA-1BT-1t≦4.5mmP 2 0 C 0 1 - F 1Pressure rangeC：Compound(-100.0~100.0KPa)V：VacuumP：Positive(-0.100~1.000 MPa)F1：1/8" PTF2：1/8" NPT(0.0~-101.3KPa)-Blank:With 2 meter cableQD：With M8, 4 Pin male connector01：2 NPN output & 1 Analog output02：2 NPN output03：2 PNP output & 1 Analog output04：2 PNP output-Output Specif ic atio nsCable Length/ConnectorKF3：G1/8"KP20-C：Panel adapter + Front protective lidKP20-A：Mounting bracket (BT-1+BT-2)KP20-B：Panel adapter (PA-1+PA-2)(PA-1+PA-2+FPC-1)Option spare part3142QD PINOUTPressure PortUnit:mmUnit:mmFPC-11Rated pressure rangeOperating /Setting pressure rangeWithstand pressureFluidPower supply voltageCurrent consumptionSwitch outputHysteresis modeResponse timeOutput short circuit protection7 segment LED displayIndicator accuracyIndicator-100.0 ~ 100.0kPa 0.0 ~ -101.3kPa-0.100 ~ 1.000MPa10.0 ~ -101.3kPa0.000 ~ 1.000MPakPaMPa2kgf/cmbarpsimmHgInHgmmH O2Set pressure0.10.0010.001-0.01- 0.0010.010.010.1---10.10.1Air, Non-corrosive gases ,incombustible gases12 to 24VDC ±10%, Ripple (P-P) 10% or less≦55mA≦±0.2% F.S. ±1digitFixed(3 digits)≦2.5ms (chattering-proof function: 24ms, 192ms and 768ms selections)Yes3 1/2 digit LED display (Sampling rate: 5 times/1sec.)≦±2% F.S. ±1 digit (ambient temperature: 25 ±3°C)Green LED (OUT1) Red LED (OUT2)SPECIFICATIONS-100.0 ~ 100.0kPa(Vacuum) (Positive)KP20C- - KP20V- - KP20P- -(Compound)Repeatability(Switch output)Hyst eresi s Window comparator modeAmbient temp. rangeAmbient humidity rangeWithstand voltageEnclosureInsulation resistanceVibrationShockTemperature characteristicPort sizeLead wireWeightOperation/Storage: 35 ~ 85% RH ( No condensation)case1000VAC in 1-min (between and lead wire)IP4050Mohm min. (at 500VDC M, casebetween and lead wire)2980m/s (100G),3 times each in direction of X,Y and Z≦±2% F.S. of detected pressure (25°C) at temp. Range of 0~50°CF1:1/8"PT, F2:1/8"NPT, F3: G1/8"2Oil-resistance cable(0.15mm )Operation: 0 ~ 50°C,Storage:-20 ~ 60°C ( No condensation or freezing)Appro*105g(with 2-meter lead wire),Appro*71g(with male connector )Total amplitude 1.5mm,10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X,Y and ZEnvironmentresolutionAdjustable3 times of rated pressure range 1.5 times of rated pressure rangeOutput voltage: 1 to 5V ≦±2.5%F.S.(within rated pressure range)Linearity: ≦±1% F.S.Analog output Output voltage: 1 to 5V≦±5%F.S.(within rated pressure range)Linearity: ≦±1% F.S.*(Only type )KP20 -01- KP20 -03-,*(O nly ty pe , )KP20 -02- KP20 -04-36×36 ± 0.3mmKP20 - 01- -KP20 - 03- -NPN outputPNP outputKP20 - 04- -PNP outputKP20 - 02- -NPN outputDC(-) (Blue)OUT2 (White)OUT1 (Black)(Orange)DC(+) (Brown)DC12-24VL o a dL o a dSwitch main circuit1KΩDC(-) (Blue)OUT2 (White)OUT1 (Black)(Orange)DC(+) (Brown)DCDC12-24V1KΩL o dL o a dSwitch main circuitDC(-) (Blue)OUT2 (White)OUT1DC(+) (Brown)DC12-24VL o a dL o a dSwitch main circuitDC(-) (Blue)OUT2 (White)OUT1 (Black)DC(+)DCDC12-24VL o a dL o a dSwitch main circuitaaOONPN:open collector 2 outputs Max. load current : 80mAMax. supply voltage: 30VDCResidual voltage :≦1V (load current 80mA )PNP:open collector 2 outputs Max. load current : 80mAMax. supply voltage: 24VDCResidual voltage :≦1V (load current 80mA )www.kita.com.tw Rev.1.0 |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine