Kenwood NXR-5700-E Instruction Manual

Also see for NXR-5700: Instruction manual Instruction manual Instruction manual Instruction manual Service manual

Kenwood NXR-5700-E Instruction Manual Manual pdf 1 page image

1UNPACKING AND CHECKING EQUIPMENTNote: The following unpacking information is for use by yourKENWOOD dealer, an authorized KENWOOD service center, or thefactory.Carefully unpack the repeater. We recommend that you identifythe items listed in the following table before discarding thepacking material. If any items are missing or have been damagedduring shipment, file a claim with the carrier immediately.Item Part Number QuantityFront glass B10-2781-XX 1Dressed screw N08-0563-XX 1Bracket J29-0725-XX 2Flat head machine screw N32-4008-XX 4Handle K01-0421-XX 1DC cord E30-3427-XX 1Lead wire with connector (15 pin) E31-3228-XX 1Fuse (15 A) F52-0042-XX 1SYNC cable E3A-0177-XX 1Instruction manual B5A-0714-XX 1INSTALLATIONTo install the handles onto the front panel of the repeater, alignthe handles with the holes on the front panel, then secure thehandles using the supplied screws.Consult your dealer for installing the repeater and antenna.MICROPHONEConnect an optional KMC-30, KMC-35, KMC-9C, or KMC-53KENWOOD microphone to the MICROPHONE jack on the frontpanel.OCXO UNIT (KXK-3): OptionThe OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator(OCXO) unit.NOTICES TO THE USER◆ Government law prohibits the operation of unlicensed radiotransmitters within the territories under government control.◆ Illegal operation is punishable by fine and/or imprisonment.◆ Refer service to qualified technicians only.◆ This repeater is intended for use as a fixed base station withthe antenna located outdoors on the rooftop or on an antennatower.◆ This repeater is designed for a 13.2 V DC power source.Never use a 24 V DC or higher source to power the repeater.◆ Use only the supplied DC cord.◆ Do not remove the ferrite core attached to the DC cord. Doingso may cause interference with radio communications.◆ Do not put anything on top of the repeater. This will obstructheat dissipation.THANK YOU!We are grateful you purchased this KENWOOD repeater.PRECAUTIONS• Do not expose the unit to rain or moisture; to prevent fire orelectric shock.• Do not open the unit under any circumstances; to avoid riskof electric shock.• Do not expose the unit to long periods of direct sunlight, norplace it close to heating appliances.• Do not place the unit in excessively dusty and/or humidareas, nor on unstable surfaces.• Do not put the plastic bag used for packing of this equipmenton the place which reaches a small child's hand. It willbecome a cause of suffocation if it wears flatly.• Always switch the transceiver power off before installingoptional accessories.• If you detect an abnormal odor or smoke coming from theunit, disconnect the power from the unit immediately. Contactyour KENWOOD service center or dealer.B5A-0714-20 (E)VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATERINSTRUCTION MANUALNXR-5700/ NXR-5800◆ Do not install the repeater in explosive atmospheres(inflammable gas, dust particles, metallic powders, grainpowders, etc.).Firmware CopyrightsThe title to and ownership of copyrights for firmware embedded inKENWOOD product memories are reserved for JVC KENWOODCorporation.Information on Disposal of Old Electrical and Electronic Equipment and Batteries(applicable for countries that have adopted separate waste collection systems)Products and batteries with the symbol (crossed-out wheeled bin)cannot be disposed as household waste.Old electrical and electronic equipment and batteries should berecycled at a facility capable of handling these items and their wastebyproducts.Contact your local authority for details in locating a recycle facilitynearest to you.Proper recycling and waste disposal will help conserve resourceswhilst preventing detrimental effects on our health and the environment.The AMBE+2TM voice coding Technology embodied in this productis protected by intellectual property rights including patent rights,copyrights and trade secrets of Digital Voice Systems, Inc. Thisvoice coding Technology is licensed solely for use within thisCommunications Equipment. The user of this Technology is explicitlyprohibited from attempting to extract, remove, decompile, reverseengineer, or disassemble the Object Code, or in any other wayconvert the Object Code into a human-readable form. U.S. PatentNos. #8,315,860, #8,595,002, #6,199,037, #6,912,495, #8,200,497,#7,970,606, and #8,359,197.© 2017NOTIFICATIONThis equipment complies with the essential requirements of Directive2014/53/EU.This equipment requires a licence and is intended for use in the countriesas below.AT BE DK FI FR DE GR IS IEIT LI LU NL NO PT ES SE CHGB CY CZ EE HU LV LT MT PLSK SI BG RO HR TRISO3166Hereby, JVCKENWOOD Nederland B.V. declares that the radioequipment types NXR-5700-E, NXR-5800-E are in compliance withDirective 2014/53/EU.The full text of the EU declaration of conformity is available at thefollowing internet address:http://www.kenwood.com/cs/com/ecdoc/(Note: The detail type designations are described in the EUdeclaration of conformity.)Model Frequency range Max. output powerNXR-5700-E TX/RX 136.000 - 174.000 MHz 25 WNXR-5800-E TX/RX 400.000 - 470.000 MHz 25 W