Kirstein BEATFOXX SurfRider WBS-18L Manual
  |
WBS-18L SurfRider Bluetooth Speaker WBS-18L SurfRider Bluetooth Speaker WBS-18L SurfRider Bluetooth SpeakerArt. Nr..: 00066225 Important Safety PrecautionsWhen using your Bluetooth Mobile Speaker, followthe basic safety precautions:1. Keep the device and charging cable away fromexcessive heat.2. Do not operate this device with a damaged cable orafter it has been damaged in any way.3. Do not disassemble your device.4. Charge the device fully for at least 3 hours before usingit for the first time5. The Musikhaus Kirstein is not liable for personal injurycaused by non-compliance with the safetyrecommendations and warnings. This also applies to allother damage in whatever form.Functional buttons of the speaker1. "-" a short press lowers the volume. Press and hold toaccess the last track in the playlist;2. Key to activate the hands-free function;3. "+" Short press increases the volume. Press and holdto access the next track in a playlist;4. Charging port(Backside) and LED indication Light5. On / off switch.Switch device on / offTo switch on and off, press button 5 for approx. 2-3seconds to start or switch off the device. A tone confirmsactivation.Change volume / play songsTo get the maximum volume, you should also set thevolume control of your audio source (smartphone) to themaximum level.Pressing "+" or "-" a little longer (approx. 2 seconds) willtake you to the next or previous song.Charge the deviceConnect the supplied USB charging cable to the chargingport of your speaker and then to a suitable USB port on acomputer, notebook or power bank to charge the internalbattery of your speaker.The charging socket can be found on the rear / lower sideof the speaker under the silicone tab with the DC5V label.After charging, close it again with a firmpressure to ensure the water-repellent functionLEDs when charging your speakerRed LED lights up: charging is in progress.Red LED goes out: charging is complete.LED mode/blinking color effectTo turn the color-blinking mode of the LEDs on or off.switch off or change, briefly press buttons (1) and (3) of thespeaker at the same time. By pressing simultaneouslyseveral times, you switch through the different flashingvariants.Pairing the speaker with Bluetooth devices1. Make sure your Bluetooth audio source(e.g. smartphone) is no more than three meters awayfrom your speaker.2. Switch on the speaker as described above.The small round LED light flashes blue to indicate thatpairing mode is active.3. Switch on the BT function on your sound source (e.g.smartphone) in the menu.After a few seconds the pairing name "WBS-18L" shouldappear on the display. Confirm this in the menu andconnect the two devices with each other.You should also find further detailed information on thispoint in the manual of your smartphone model.After successful pairing, the blue LED lights upcontinuously and you can listen to the music from yourBluetooth audio source via speakers.4. Press and hold the button (5) to disconnect theBluetooth connection.Thank you for purchasing this product. To ensure you will becompletely satisfied with this product, read and understand thismanual carefully before use. Keep the manual in a safe place.The Operating Manual must be passed on to all subsequentusers.Follow the Operating Manual!Package ContentsBluetoothSpeaker USB Charging cable User manual +snap hookSpecificationsBluetooth version: 5.0Loudspeaker: 4Ω / 5WBuilt-in battery: Li-ion 1000mAhDimensions: 102mm(L)*93mm(W)*43mm(H)SNR: >80dBBluetooth Frequency: 2.402-2.480 GhzBT-Distance/ Trans.Power: up to 10m / <20mWTWS TransmissionDistance: up to 5mCharging time Approx. 2,5 hoursWeight: 170 gSpeaker dimension 45 mmCharging S V, 500mA |
Related manuals for Kirstein 00066225
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine