LAN Power LP-2334 Installation Manual
   |
LP-23345 Port PoE Unmanaged 10/100Mbs Switch/Extender(4 Ports Full PoE Power-up to 15.4 Watts per Port with 1 UPLINK Port up to 100Mbs)Installation GuidePurpose of this GuideThis Guide provides information and procedures for the product installation and operation of the 5 Port PoEUnmanaged 10/100Mbs Switch/Extender (LP-2334). This document is intended for technical personnel andto use this document effectively, you should have a working knowledge of Local Area Networking (LAN)concepts and hardware installation. In addition, you should be familiar with the following: Connection ofPatch Cables with RJ45 connectors and the LAN addressing map for your particular Network, Mounting ofNetwork hardware in a 19” equipment rack and local practices for power cord connections.IMPORTANT SAFETY INSTRUCTIONS FROM LAN PowerRead and keep these instructions. Follow all instructions and heed all warnings. Do not use this equipmentnear water and clean only with a dry cloth. Do not block any equipment ventilation openings. Install inaccordance with manufacturer’s instructions. Do not install near any heat sources such as radiators, heatregisters, stoves, or other apparatus (including amplifiers) that produce heat. Unplug this equipment duringlightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel.Servicing is required when the equipment has been damaged in any way, liquid has been spilled, or objecthas fallen into the equipment, the equipment has been exposed to rain or moisture, does not operatenormally, or has been dropped. The AC mains outlet, or appliance coupler shall be readily available to theoperator as a means of power disconnection.CAUTION – These servicing instructions are for use by qualified service personnel only. To reduce the risk ofelectric shock, do not perform any servicing other than that contained in the operating instructions unlessyou are qualified to do so.If You need Help or additional support relating to the contents of this Guide, please contact LAN Powerusing one of the following methods: Phone: 1-510-275-4572 Fax: 1-510-824-5654 Mail: LAN Power, 47835Westinghouse Drive, Fremont, CA 94539 Web Address: www.lan-power.com Email: support@lan-power.comBefore contacting LAN Power for technical support, please have the following information ready: theproduct model number and unit serial number. A description of the failure or symptoms of problem. Adescription of any action(s) already taken to resolve the problem (e.g., changing ports, rebooting the unit,etc...). The type of End device being powered including Manufacturer name and part number. Poweringrequirements of the End device. A description of your Network environment (layout, Ethernet switchdescription, cable type, etc...). The unit history (i.e., have you returned the unit before, is this a recurringproblem, etc...)Please note only qualified personnel should install this unit andread instructions before attempting to install this unitVerifying Contents of Package - Unpack the PoE Injector and verify that you have thefollowing items: LP-2334 5 Port PoE Unmanaged 10/100Mbs Switch/ExtenderNOTE: THE LP-2334 DOES NOT INCLUDE A POWER SUPPLY and MUST BE PURCHASEDSEPERATELY. Use either the LAN Power LP-2575 (Single Port ULTRA High Power MidspanPoE Injector) or LP-2304PSU (AC Mains Power Supply Unit)Technical Considerations - Before you mount the 5 Port PoE Unmanaged 10/100Mbs Switch/Extenderto a fixed location, consider all of the following: Determine optimal placement, check patch cord routingand AC outlet location. Collect and document Network information as required. Ensure the CAT 5 (orhigher) cable length from the LP-2334 to the Powered End IP device does not exceed 328 feet/100 meterstotal length.Powering Up and Installing the 5 Port PoE Unmanaged 10/100Mbs Switch/Extender1.)Connect the Power Supply Unit for the LP-2334 (which IS NOT SUPPLIED with unit and must bepurchased separately) The LP-2334 can be powered with one of the following units:a.) Connecting a LAN Power LP-2575 (Single Port ULTRA High Power Midspan PoE Injector) – Connecta LAN data cable - CAT 5 (or higher) from the RJ45 port labelled OUT (bottom left) of the LP-2575 andthe other end of the cable to the back of the LP-2334 into the RJ45 Port (far right RJ45) labelled PoEPOWER INPUT (Min. 65 Watts) AND DATA OUTPUT (Max. 100Mbs). Once connected the POWERIN LED on the front of the LP-2334 will illuminate solid green.IEEE 802.3afCompliant |
Related manuals for LAN Power LP-2334
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine