Lamphus SolarBlast SBWL14 Quick Start Manual
Online LED Store S2B Inc. ©2016 All Rights ReservedLAMPHUS ® SolarBlast TM SBWL14Compact High Intensity LED Windshield Mount StrobeLightSKU: PSZLEDSTB0401 Rev.1www.online-led-store.comPhone: 1-855-LED-ONLINE (1-855-533-6654)Fax: (909) 575-6722E-mail: support@online-led-store.comIMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.• Installer of this product must have a good understanding of automotiveelectronics, systems, and procedures.• In the case that holes must be drilled in order to properly mount the product, theinstaller must examine both sides of the mounting surface before drilling begins.It is the installer’s responsibility to be sure that no vehicle components or vitalparts could be damaged by the drilling process. De-burr any holes in order toremove metal shards and remnants. Use grommets in all wire passage holes.• If this manual states that this product may be mounted with suction cups,magnets, tape, or Velcro®, clean the mounting surface and dry thoroughly priorto applying any adhesives for maximum adhesion.• Do not attempt to activate or operate this product under hazardous drivingsituations.• Deployment area of the vehicle air bags must be cleared. Do not install thisproduct or route any electrical wires near the air bags deployment areas. Refer toyour vehicle owner’s manual for the air bag deployment area. Products or wiresmounted in the air bag deployment area will damage, reduce the effectiveness ofthe air bag, or even act as a projectile which may cause serious injury or death.The user/installer of this product assumes full responsibility in determining theproper mounting location while prioritizing the safety of all passengers in thevehicle.• This product contains strobe light(s), halogen light(s), high-intensity LEDs, or acombination of these components. Do not look directly into the lights.Momentary blindness and/or injury to the eyes could result.Functions of Power Adapter:Rocker On/Off Switch w/ LED Indicator Light- To turn unit on and off. LED indicator light illuminates red whenthe unit is powered on.Momentary Rocker Switch- Press for a second and release to advance the unit to the nextflash pattern.- Press and hold for 3 seconds to advance the unit to SteadyMode.Flash Patterns:1. Off Mode2. Single Burst - Split3. Single Burst - All4. Single Burst - Combination5. Double Burst - Split6. Double Burst - All7. Double Burst - Combination8. Quad Burst - Split9. Quad Burst - All10. Quad Burst - Combination11. Single Flash - Split12. Single Flash - All13. Single Flash - Combination14. Double Flash - Split15. Double Flash - All16. Double Flash - Combination17. Quad Flash – Split18. Quad Flash - All19. Quad Flash - Combination20. Super Flash - Split21. Super Flash - ALL22. Super Flash – Combination23. Single Flash w/ Quad Burst -Split24. Single Flash w/ Quad Burst - All25. Accelerator - Split26. Accelerator - All27. Combination Mode28. Combination Burst Mode29. California Steady30. California Steady Reverse31. Steady Mode32. Cycle ModeWiring (with power adapter detached)WANRING! All customer supplied wires that connect to thepositive terminal of the battery must be sized to supply at least125% of the maximum operating current and FUSED at thebattery to carry that load. DO NOT USE CIRCUIT BREAKDERSWITH THIS PRODUCT!RED – To 12/24V Power SourceBLACK – To Chassis GroundYELLOW – Synchronization and Pattern Selection- Connect YELLOW of all units together to enable synchronization.- Apply YELLOW to BLACK for a brief second will advance unit tothe next flash pattern.- Apply YELLOW to BLACK for more than 3 seconds will advanceunit to Steady Mode.WHITE – Group Selection (Note: group selection can only be configuredwhen the units are off)- Units with its WHITE connected to the RED will be groupedtogether as GROUP 1.- Units with its WHITE NOT connected to the RED will be groupedtogether as GROUP 2.- Units of GROUP 1 and GROUP 2 will flash alternately if it’sYELLOW are connected to each other.Specifications:Input Voltage: 12/24 VDC +/- 20%Input Current: 100 – 600/50 – 300 mAPMSOutput Power: 1 – 8 WATTS |
Related manuals for Lamphus PSZLEDSTB0401
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine