Landscape Forms FGP Installation Manual
Also see for FGP: Installation guide
   |
INSTALLATION PROCEDURE FOR LIGHT POLE:1. Lift the light pole into position over the installed anchors (refer to FGP area lightanchor kit installation guide) as shown in Fig. 1. Ensure that the base plate is restingon all four washers.2. Install washers and hexs nut as shown in Fig. 2.3. Plumb and level the pole and tighten all anchors.4. Connect line-in wires to driver plate assembly. Pass wires through strain relief. SeeFig. 3. Refer to wiring diagrams on page 3.5. Ensure that the wire harness connectors are pulled through the top of the driverplate assembly through the front cavity. This is to connect the luminaire wiring.6. Gently insert the driver plate assembly into the top of the pole. Ensure the front ofdriver plate assembly is in the correct orientation. See Fig. 3 and 4.7. Apply downward pressure to compress the gasket. Tighten the six hex bolts equallyusing a 13mm wrench until snug. Ensure that once tightened, the driver plateassembly rests in the center of the pole.8. Connect luminaire wiring to driver plate assembly, see Fig. 5.9. Gently push wires down inside of driver plate assembly. Set Luminaire on top ofdriver plate assembly, ensuring that the luminaire mount plate is seated properly onthe top of the driver plate assembly. Use an 8mm hex key to install M10 x 55m sockethead cap screw and sealing washer to secure luminaire to top of pole.10. If twist lock receptacle is specified, remove shorting cap and install photo-eye control(not included), see Fig.6.11. Install the cover plate as shown in Fig. 7 and 8. Use a 5mm hex key to tighten internalsocket head cap screws to secure the two halves together.Tools Required• Safety glasses• Wrenches, 1-1/4” , 13mm• Screwdrivers, Phillips and straight blade• Wiring tools and connectors• Proper personnel, crane or lift for hoisting unit onto anchors• Level• Dimming control, if required• Hex keys, 8mm with 10-12” extension, 5mm• Twist lock photo eye control, if requiredLandscape Forms is not responsible for site preparation and footings. Refer to theinstallation guide for the FGP light anchor kit for installing the anchor bolts.CAUTION! This unit is heavy. To avoid injury or damage to the finish, we recommendusing a crane or lift for hoisting the unit onto the anchors.WARNING! Pole mounted luminaires must be attached either before or immediatelyafter pole installation. Failure to do so may cause vibration damage to the pole and willvoid the pole warranty.ASSEMBLE WITH CARE! Pangard II Polyester Powdercoat is a strong, long-lasting finish. Toprotect this finish during assembly, place unwrapped powdercoated parts on packaging foam orother non-marring surface. Do not place or slide powdercoated parts on concrete or other hardor textured surface – this will damage the finish causing rust to occur. Use touch-up paint on anygouges in the finish caused by assembly tools.Luminaire2x - Cover plate half Twist lock receptacle,optionalInstallation GuideFGP Area Lightwww.landscapeforms.com Ph: 800.521.2546Date: March 19, 2021Page 1 of 3Included componentsShorting cap forTwist lock, optionalPoleDriver plateassembly 1x - M10 x 1.5 x 55mmsocket head cap screwwith sealing washerINSTALLATION PROCEDURE FOR OPTIONAL PHOTO EYE:Refer to wiring diagram for wiring details.1. Remove the twist lock cap from the top of the light.2. Loosen the two phillips head screws two turns.IMPORTANT! Do not remove the screws. Loosen just enough to rotate the receptacle.3. Rotate the receptacle until the arrow points north. Tighten the screws.4. Install the photo eye (not supplied with unit) rated for proper line voltage (277v,1.5A).WARNING!: LED cartridge and driver are not rated for connection or disconnection whileenergized. Doing so may damage LEDs and will void the warranty. Disconnect incomingpower before making or breaking any electrical connections. |
Related manuals for Landscape Forms FGP
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine