Larson Electronics EPS-PB10-GRN-2XC Instruction Manual

Larson Electronics EPS-PB10-GRN-2XC Instruction Manual Manual pdf 1 page image

EPS-PB10-GRN-2XCLarson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1 of 3Explosion Proof Green Mushroom Push Button Switch(2) Contact Blocks - Class I and II, Division 1 and 2Instruction ManualThank you for your purchase of the Larson Electronics EPS-PB10-GRN-2XC.)WARNING:READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.CRITICAL SAFETY INSTRUCTIONS:• INSTALLATION SHOULD ONLY BE CONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANYRELEVANT LOCAL BUILDING CODES.• RISK OF FIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICALSYSTEMS. IF NOT QUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.• BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.• MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.• TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARPOBJECTS. SUITABLE FOR DAMP LOCATIONS.IMPORTANTREAD CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTUREREFERENCE. THE EPS-PB10-GRN-2XC MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICALCODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THISPRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THEINSTALLATION OR PERFORMING ANY MAINTENANCE.RISK OF FIRE/ELECTRIC SHOCK – DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.RISK OF PERSONAL INJURY – FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.RISK OF BURN – ALLOW FIXTURE TO COOL BEFORE SERVICING.WARNINGTO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALLAPPLICABLE ELECTRICAL CODES.TO AVOID ELECTRIC SHOCK:• BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.• PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDINGCONDUCTOR.TO AVOID EXPLOSION:• MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.• ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUSATMOSPHERE.• DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCTNAMEPLATE.• DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED ORDAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.• ALL FASTENERS SHOULD BE PROPERLY SEATED.The Larson Electronics EPS-PB10-GRN-2XC explosion proof single green push button switch is designed for use inhazardous work areas, such as chemical plants, oil refineries and settings where combustible gases or dust may bepresent. This 10-amp device features the following explosion proof ratings: Class I Division 1 and 2; and Class II Division1 and 2. In industrial and commercial settings, the front-operated push button switch may be used to support basicfeatures of machines lacking electrical circuits for control. When ordering this unit, buyers may choose from 1/2" and 3/4",dead end and feed thru options.

/ 3

Related manuals for Larson Electronics EPS-PB10-GRN-2XC