Laser Pegs NFL003 Lift the House Assembly Instruction Manual

Laser Pegs NFL003 Lift the House Assembly Instruction Manual Manual pdf 1 page image

x2 AVvEach Laser Peg® is color coded on the circuit board insideeach shape. There is No LED In The 90 Degree Peg.Laser Pegs® link thatallows you to connect toother construction kits.Triangle PowerBaseColorCodeAll additional model instructions canbe downloaded at www.LaserPegs.comMODEL INSTRUCTIONSLaser Pegs® StackableLaser Peg® Parts ListConstruction Parts ListSQUAREPEG90° PEG45° PEGY PEGThere is No LED In The 90 Degree Pegx4x4x2x1x2x4x4x4x2 x2x2x4x8x4x2x8x8x2HELMET PEGSTRAIGHTT-PEGSQUAREM-M PEGx1x2x2x2x2x2x1 x1 x2x4x2x2x2x4x6x2x2x2x2x2x2x4STACKABLE FOOTBALL PEGx2x2x2WHEEL PEGx4Please read manual before you begin! Failure tofollow this manual’s instructions may result indamage to the Triangle Power base, AC adapterand/or Laser Pegs®. Not adhering to thesedirections will void the manufacturer’s warranty.Packing has to be kept since it containsimportant information.Compatible with other construction kitsWARNING:CHOKING HAZARD-Small parts.Not for children under 3 yrs.Do not submerge in water.Construction CompatibleEN71, RoHS COMPLIANTThis product complies toall safety requirementsof ASTM F 963For Boys And GirlsAges 5 And Up24 Models+LIGHTEDCONSTRUCTION SET INCLUDES:• 32 Laser Pegs®• 96 Construction Parts• Triangle Power Base• Instruction ManualRequires 3 AA BatteriesBatteries NOTIncludedAny creation you can buildTo construct with Laser Pegs®, slide two pieces together to form aconnection. Slide each piece on and off smoothly. To build away from theTriangle Power Base, use the peg cord in one of the top three peg holes toilluminate your model! The 90° pegs are essential to construction but theyDO NOT ILLUMINATE.This manual is copyright and cannot be reproduced or used online without LaserPegs®Ventures LLC permission. Copyright 2013 © All Rights Reserved US Patent#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®VenturesLLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.comwww.LaserPegs.comConnecting PegsPress buttonto turn on/offPush button to cyclethrough 3 differentlight settings.Power Button Peg HolesAC AdapterConnectionRemove the three Philips headscrews with a 4mm screw driver.Requires (3AA) BatteriesUsing anAC AdapterRemove all batteriesfrom Laser Pegs® powerbase before using the5 volt AC adapter.When using an ACAdapter, NEVERplace the adapterplug into the Tri-angle power basetop peg holes.When Using BatteriesWARNING! Each Laser Peg® draws current from the batteries. Therefore, the morepegs you use, the quicker you will deplete your battery power! As the powerweakens, the current will slowly fail and some Laser Pegs® will illuminate (typicallythe reds and yellows) and some won’t. When the Laser Pegs® dim the Laser Pegs®are not broken, they just need stronger batteries or an AC Adapter.You have 3 simple options...1. Use a 5 volt AC Adapter –available from www.LaserPegs.com2. Change the batteries.3. Use high quality batteries. They will last a little longer, but they will still depleterapidly the more laser pegs you connect!*To avoid short-circuits, keep metal objects andother un-authorized materials from obstructingthe peg holes.The AC adapter and the power base are to be regularly examined for damageto the cord, plug, enclosure and other parts, and in the event of such damage,they must not be used until the damage has been repaired.1. Remove screws.2. Place three AA batteries in the correctposition - as displayed inside the TrianglePower Base.3. Push RED button to turn on!4. Do not mix old and new batteries.5. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium)batteries!6. Exhausted batteries are to be removedfrom the power base.7. Never connect more than 200 Laser Pegs®8. Non-rechargeable batteries are not to berecharged.9. Rechargeable batteries are only to becharged under adult supervision.10. Rechargeable batteries are to be removedfrom the toy before being charged.11. Batteries are to be inserted with thecorrect polarity.12. The supply terminals are not to be short-circuited.Never connect more than 200Laser Pegs® when using a 5 volt(2000mA) AC Adapter.FOOTBALL PEGHELMET PEGNFL Series Helmet and Football PegYour NFL Series Laser Pegs® kit comes with a set of licensed NFL teamdecal stickers. There are two stickers per team included. These stickers canbe affixed to the sides of the Helmet Peg or the the Football Peg.Your NFL Series Laser Pegs® kit also includes bonus material from theNFL Rush Zone.Affixing NFL Team Logo StickersThere will be two (2) sheets of NFL logo stickers included inside eachindividual NFL Series Laser Peg® kit. These sheets of stickers will have aset of two (2) team logos that can be placed on either side of the Helmetor Football Peg. Before applying stickers to the pegs, it is advisable to firstwipe any dirt, oil or residue that maybe on the surface of the pegs due tohandling with a clean dry cloth. This will help ensure proper adhesion tothe peg’s surface.The NFL Series Laser Pegs® kit includes the Football and Helmet Peg.These shapes can be used with any other existing Laser Pegs® kit. Both theFootball and Helmet Pegs illuminate.Supplied NFL team stickers will be reflected so that they will remain inthe correct orientation when they are applied to either side of the Helmetor Football Pegs.WARNING! Do not ingest stickers or backing sheet. This could be potentiallydangerous and may cause severe injury. So keep away from small children.Apply Sticker toside of Helmet Peg.Apply Sticker to sideof Football Peg.The NFL SeriesLaser Pegs® kitFootball Peg has onlyone mating end.The NFL SeriesLaser Pegs® kitHelmet Peg(s) Isincluded.Additional stickers are includedLIMITEDEDITIONWhen applying the NFL SeriesLaser Peg® Team Logo StickersTRIDENT PEG