LumenRadio W-BACnet Manual
Also see for W-BACnet: Manual
  |
MANUAL W-BACnet and W-BACnet PRO LUMENRADIOCopyright © LumenRadio AB 2023, All Rights Reserved www.lumenradio.comAPPLICATION AREAThe W-BACnet product transmits BACnet MS/TP frames wirelessly. It is designedto be used indoors only. If used outdoors, this unit must be installed in a protec-tive enclosure with minimum IP65 rating. The product is intended to be used asa BACnet MS/TP cable replacement.GENERALThis manual applies for both the DIN rail and the wall mounted version of theW-BACnet product. All relevant personnel must acquaint themselves with theseinstructions before installation. Warranty is voided if the product is not hand-led accordingly with the outlined instructions. Any damage to the product orparts due to improper handling will void the warranty. Do not use the productif damaged. For additional W-BACnet documentation scan the QR-code or visitwww.lumenradio.com.WARRANTYThe warranty or service agreement will be deemed void if:(1) The product is repaired, modified, or changed, unless such repair,modification or change has been approved by LumenRadio AB; or(2) The serial number on the product has been made ineligible or is missing.ELECTRICAL SAFETYOnly qualified electricians or service personnel trained by LumenRadio may per-form interventions in connection with electrical installation. Always follow local/na-tional rules when performing this type of electrical installation. When connectinga 24 V isolation transformer, this must be done in accordance with IEC 61558-1.TECHNICAL DATACasing Wall mount DIN railPower supply AC: 24 VAC ±10% 24 VAC ±10%Power supply DC: 24 VDC ± 15% 12–24 VDC ± 15%Max. power consumption: 2.5 W 2.5 W24 V output max. power: 10 W N/AAuto resettable fuse: Yes YesSolid cable rating, connector: 0.14 - 0.5 mm2 0.2 - 1.5 mm2Stranded cable rating, connector: 0.2 - 0.5 mm2 0.2 - 1.5 mm2Conductor sizes (AWG): 24 - 20 24 - 16Range per hop (Line-of-sight): 500 m 700 mRange per hop (Indoor with walls): 50 - 70 m 50 - 70 mIP class: 40 X0Dimensions (W x H x D): 86.0 x 86.0 x 25.5 36.5 x 93.0 x 58.7Weight: 95 g 87 gCasing Wall mount/DIN railPower source restriction: Only to be powered by a UL listed LPSpower supply of max 15 WAmbient operating temperature: -20 to +55°CAmbient storage temperature: -30 to +80°CRelative humidity: 10 - 95% non-condensingMaterial: ABS UL94-V0Color: WhiteFrequency band: 2.45 GHz, ISM band (2400-2483 MHz)Baud rate: 9600, 19200, 38400, 76800 bpsNumber of Nodes: 100 Nodes in one wireless networkMax. number of hops: 8 hops in the meshing networkINSTALLATIONInstall the W-BACnet unit next to the device it should be connected to.1. Confirm that the W-BACnet unit has no visible damage.2. Wall mount: The enclosure is wall mounted and fits onto a junction box. Startwith mounting the backplate of the enclosure.DIN rail: The DIN rail has a clip-on mounting. Place it onto the DIN rail.3. Connect the power supply and the BACnet device to the W-BACnet unit,as shown to the right. For a wall mounted unit, use the rear and/or topknockouts for cable entry.4. All W-BACnet units are factory set for Node operation, without the need foradditional configuration. If mixing serial configuration in the system, adjustthe dip switches accordingly.5. Check that the W-BACnet unit and its wiring are securely mounted (if theunit is powered this will be indicated by the LEDs).6. Wall mount: Secure the front plate to the mounted back plate.The device is now ready for commissioning.W-BACnet is an end device with internal termination resistor.THE PACKAGING CONTAINS1 x W-BACnet wall mount or1 x W-BACnet wall mount PRO or1 x W-BACnet DIN railand 1 x Instruction leafletSYSTEM OVERVIEWThe W-BACnet comes in three different versions; wall mount, wall mount PRO andDIN rail. A W-BACnet network consists of a single W-BACnet Gateway connectedto the BACnet device or controller using an RS485 cable. It can be up to 100W-BACnet Nodes in one network, each of them connected to one BACnet deviceover RS485, or in the PRO case, up to four BACnet Devices on one wall mountPRO. Every device can act as either a Gateway or a Node, selectable by the 3 poleswitch - see Commissioning section.Each W-BACnet Node will scan to find the connected BACnet devices’ BACnetaddresses. The scanning is done by querying every BACnet address, hence theprocess may take up to 15 seconds. In this case, the W-BACnet Node will indicatered on the data LED – see System mode and status.POWER AND RS485 CONNECTIONThe W-BACnet uses a half-wave rectified circuit. It should not share a transformerwith a full wave rectified VAC source. The W-BACnet wall mount units have 24VAC/VDC power in/out connection and connection for BACnet MS/TP commu-nication via RS485. The W-BACnet DIN rail units have an 12-24 VDC or 24 VACconnector at the top of the product next to the external antenna and an RS485connector at the bottom.www.lumenradio.comScan for additionalinformationW-BACnet NodeBACnet MS/TP cableWireless MeshW-BACnet PRO NodeW-BACnet GatewayMS/TP ControllerMS/TP deviceMS/TP deviceMS/TP deviceMS/TP deviceMS/TP deviceMS/TP device MS/TP device MS/TP device MS/TP deviceMS/TP deviceFCC ID: XRSTIMOMWAN201 (Wall mount)XRSTIMOMWAN301 (DIN rail)IC ID: 8879A-TIMOMWAN201 (Wall mount)8879A-TIMOMWAN301 (DIN rail)MET: E115504UL 62368-1CSA C22.2 No. 62368-1MANUFACTURERLumenRadio ABJohan Willins gata 6416 64 GothenburgSweden24V AC/DCA+ B- GNDG/~ G0/TG/~ G0/T+ - + -24 VAC/DC |
Related manuals for LumenRadio W-BACnet
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine