MuxLab 500762-TX Quick Installation Manual

Also see for 500762-RX: Quick installation guide

Contents

MuxLab 500762-TX Quick Installation Manual Manual pdf 1 page image

© MuxLab Inc. 94-000857-B SE-000857-B8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: videoease@muxlab.com URL: www.muxlab.comSpecificationsEnvironment HDMI 2.0 (RX) and HDMI 1.3a (TX)Devices Blu-Ray, Set Top Boxes, Media Players/Streamers, projectors, monitors, TVs, PCs,supporting HDMI.Signal Protocal/Standard HDMI 2.0 and HDCP 2.2 (RX) / HDMI 1.3a and HDCP 1.3 (TX)Video Bandwidth 225MHzNetwork Bandwidth 30Mbps (max)Latency 300msProtocols TX: Supports Multicast, RTSP, RTMP (H.264), HLS, FLV (H.264) & TSRX: Supports Multicast, RTSP, RTMP, HLS, FLV & TSConnectors One (1) HDMI connector for AV (input on TX & output on RX).One (1) RJ45S for Ethernet connection (on TX & RX).One (1) USB connector for local AV content storage via external USB drive (on RX).One (1) TosLink optical connector for digital audio extraction (on RX).One (1) 3.5mm connector for audio imbedding/extraction (input on TX & output on RX).One (1) 3.5mm connector for directional IR (on TX & RX, direction controlled via software).One (1) RS232 DB9 connector for controlling end devices (on TX and RX).One (1) 2.1mm locking power connector (on TX and RX).CablesNote: Cables not included.One (1) Cat 5e/6 or better twisted pair cables required for Ethernet (on TX and RX).One (1) HDMI cable for connecting to source (on TX) or sink (on RX) devices.Optional:One (1) 3,5mm 2CH audio cable for embedding (on TX) / extracting (on RX) audioOne (1) RS232 cable for end device control (on TX and RX).One (1) optical cable for digital audio extraction (on RX).Maximum Distance Cat5e/6: 330ft (100m) from Ethernet Switch.The unit can extend over the Internet for unlimited distance.Note: When installed in an electrically noisy environment, an STP cable must be used.Also, cross-connection reduces the effective distance depending on the grade of twistedcable used.RJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Power Source This device supports PoE (PD), an external power supply is not included. It is intended tobe powered via a PoE (PSE) Ethernet Switch. If required, an optional power supply(500993) may be purchased separately.PoE IEEE 802.3afPower Consumption 4.5WTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingDimensions 4.4” x 3.6” x 1.0” (111mm x 92mm x 25mm)Weight 0.9lbs (0.4kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 3 yearsOrder Information 500762-TX HDMI over IP H.264/H.265 PoE Transmitter500762-RX HDMI over IP H.264/H.265 PoE Receiver, 4K/60Accessories(These items are soldseparately)500920 16-Port Rackmount Transceiver Chassis500917 Wall Mount Transceiver Bracket Kit500990 IR Emitter, and 500994 IR Sensor500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU BladeHDMI over IP H.264/H.265 PoE Transmitter (500762-TX)HDMI over IP H.264/H.265 PoE Receiver, 4K/60 (500762-RX)Quick Installation GuideOverviewThe HDMI over IP H.264/H.265 PoE Transmitter (500762-TX), and the HDMI over IPH.264/H.265 PoE Receiver, 4K/60 (500762-RX) combination allows HDMI source and displayequipment to be extended locally up to 330ft. (100m) at up to 4K @ 60Hz resolution via one (1)Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint andmultipoint-to-multipoint is possible by connecting several Transmitters and Receivers to the samelocal Ethernet network. The exceptionally low bandwidth requirements of this device combinationallows for streaming audio/video content over a local network, over WiFi, and over the Internet fordistributed installations spread-out throughout the globe. The transmitter accepts a 1080p @ 60Hzvideo and streams the content to the Receiver, where the signal is up-scaled up to 4K @ 60Hz to bedisplayed on a 4K monitor. The Receiver also accepts H.264/H.265 video streams from othertransmitting devices of up to 4K @ 60Hz (4:4:4), and supports a USB 3.0 Type A connector forstoring and playback of local content from an external USB drive.The Transmitter (500762-TX) and Receiver (500762-RX) are sold separately, and support PoE(PD) if used with a PoE (PSE) Ethernet Switch. The 500762-TX comes with one (1) Transmitter,while the 500762-RX comes with one (1) Receiver. IR Emitter and IR Sensor, if required, may bepurchased separately for IR based remote control applications.For the point-to-multipoint and multipoint-to-multipoint configurations the Ethernet Switch musthave Gigabit ports, DHCP Server capability and additionally support the IGMP communicationprotocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG300 SeriesManaged Switches.The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration andutilization of the 500762 and other MuxLab Av over IP products via an Ethernet web interface.ApplicationsApplications include Audio/Video streaming over LAN/WiFi/Internet, commercial and residentialAV systems, classroom projector systems, digital signage, boardroom systems, and medicalinformation systems.

/ 2

Related manuals for MuxLab 500762-RX