MuxLab 500777-RX Quick Installation Manual
  |
© MuxLab Inc. 94-000909-A SE-000909-A2321 Rue Cohen, Montreal, Quebec, Canada. H4R 2N7Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: info@muxlab.com URL: www.muxlab.comSpecificationsSpecificationsEnvironment HDMI and USB connectivity.Devices Blu-Ray, projectors, monitors, TV, PC, laptops, servers, and Smart White Boards.Bandwidth 300MHzSignals HDMI 2.0b (4K/30 4:4:4 & 4K/60 4:2:0), USB 1.1 & 2.0 and HDCP 2.2ConnectorsNote: Cables not included.One (1) HDMI receptacleFour (1) USB type A connectorsOne (1) RJ45 for Ethernet connectivityOne (1) 3.5mm jack for Audio-OutOne (1) 3.5mm jack for Directional IROne (1) 2.1mm jack for powerMaximum DistanceBased on a maximumlength of 6.6ft (2m) ofHDMI cable per end.Cat5e/6: 330ft (100m)Note: When installed in an electrically noisy environment, an STP cable must be used. Also,cross-connection reduces the effective distance depending on the grade of twisted cable used.Latency Typical one (1) frame (16ms)Compression JPG2000Bandwidth Up to 500MbpsNetwork Requirement 1 Gig Ethernet with IGMP, Jumbo Frames and PoERJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Power Source This device supports PoE (PD), an external power supply is not included. It is intended to bepowered via a PoE (PSE) Ethernet Switch. If required, an optional power supply (500993) maybe purchased separately.PoE IEEE 802.3afPower Consumption 3WTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingDimensions 5.03” x 4.53” x 1.66 (128mm x 115mm x 42mm)Weight 1.35 lb (0.61 kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 3 yearsOrder Information 500777-RX HDMI/USB over IP PoE Wall Plate Receiver, UHD-4K500777-RX-WH HDMI/ USB over IP PoE Wall Plate Receiver, UHD-4K (White)Accessories(This item is soldseparately)500993 Universal Locking Power Supply 5VDC/2.6A US/UK/EU BladeHDMI over IP PoE Wall Plate Receiver500777-RXQuick Installation GuideOverviewThe HDMI over IP PoE Wall Plate Receiver allows HDMI and USB equipment to be connected upto 330ft (100m), with video supported at up to 4K (3840x2160) resolution @ 30Hz via one (1)Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. The USB port may be usedfor extending various USB devices including Smart Boards. Point-to-multipoint and multipoint-to-multipoint configurations are also possible by connecting several Transmitters and Receivers to thesame local Ethernet IP network via an Ethernet Switch. The HDMI/USB over IP PoE Wall PlateReceiver also supports PoE (PD) if used with a PoE (PSE) Ethernet Switch.For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch musthave Gigabit ports, Jumbo Frame capability, DHCP Server capability, PoE, and additionallysupport the IGMP communication protocol for the multipoint-to-multipoint case. MuxLabrecommends using the Cisco SG300 or SG500 Series Managed Switches.The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration andutilization of the 500777-RX and other MuxLab IP based products via an Ethernet web interface.The MuxLab Control Android and iOS Application may also be used for connectivity management,in combination with the 500811 Network Controller.ApplicationsApplications include commercial and residential AV systems, classroom systems, digital signage,boardroom systems, conference rooms, and collaborative PC systems.Installation1. Identify the connectors on the Transmitter as indicated on the product labels, see the above productview for further details. Note that the Ethernet network connector is on the rear.2. Verify that the distance between the HDMI/USB over IP PoE Wall Plate Transmitter andother MuxLab Receivers is within the specifications (see Specifications table for moredetails).3. Connect the Receiver to the HDMI display equipment with an HDMI compliant cable.3a. If the application is point-to-point, then connect one (1) Cat 5e/6 cable (or higher)coming from the Transmitter, to the RJ45 LINK connector on the Receiver. Iftransmitting over the network, use an Ethernet Switch between Transmitter andReceiver. |
Related manuals for MuxLab 500777-RX
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine