4 1To unpair a paired Bluetooth ® device, select the device in the [Delete] screen.▼ Other Setting and CheckThis setting must always be set to “Disable”.You can view the following kinds of information about the IP3NA-BHA ADAPTER:・ Firmware and hardware versions・ Bluetooth ® module information andstandard・ Installed profile versions・ Device address and name▼ SpecificationsThe Bluetooth ® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of suchmarks by NEC Infrontia Corporation is under license. Other trademarks and trade names are those oftheir respective owners.▼ IntroductionThe IP3NA-BHA ADAPTER is an adapter that connects a Bluetooth® device to a multifunctionalterminal.The table below lists the type of device that can be connected to the IP3NA-BHA ADAPTER and thefunctions supported by it.Item SpecificationDestination Multifunctional terminal bottom-unit connecter (except for economy multifunctional terminal)Bluetooth ® version Bluetooth ® version 2.0Radio interface Bluetooth ® Class1(1 to 100mW)Installed profiles ・ GAP : Generic Access Profile ・ HSP : Headset Profile・ SPP : Serial Port Profile ・ HFP : Hands Free ProfilePower consumption About 0.8 W (excluding the telephone)Power feeding method Power feeding from the multifunctional telephoneDimensions (L W H) 72mm 65mm 25mm (excluding projections)Mass About 0.1kgOperating environment Temperature: 0 to 40 , Relative humidity: 10 to 90% (no dew condensing)Restrictions Keep the IP3NA-BHA ADAPTER at least 1m apart from other IP3NA-BCH ADAPTERsand at least 3m apart from other radio equipment.=2CKTKPI?ĉĊ$CEM1-Ĵ Ĵĵ=$NWGVQQVJ*GCFUGV?&GNGVG%QPPGEVĉĊ$CEM1-=&GNGVG?&GNGVG$6&GXKEG1-!$CEM1-Ĵ Ĵ=$NWGVQQVJ?$6+PHQTOCVKQPĉĊ$CEM1-Ķ=$6+PHQTOCVKQP?(KTOYCTG8GTUKQP::ZZ*CTFYCTG8GTUKQP::ZZĉĊ'ZKVĶType of device Available function RemarksBluetooth ®headset・Originating calls to an extension or central office linePress the headset call (call control) button twice briefly anddial the numbers on the telephone.・Answering terminating callsPress the headset call (call control) button while a callterminates with a ring tone.The headset call (call control) button allows you to onlyoriginate calls from the headset and answer terminatingcalls.Any other headset-specific functions are not supported.The handset cannot be used while you are talking with theheadset on. You cannot switch to the headset to use whileyou are using the handset, either.・The ringing of callsterminating to the headset islinked with that of theterminal, though someringing features, such asoff-hook ringing are notsupported.For latest information aboutrecommended products,please consult with yoursystem provider for a list ofcompatible headsets.・A headset with built-in Bluetooth ® supporting the HFP/HSP profiles can be connected to the IP3NA-BHAADAPTER.・The receiver volume can be controlled with the multifunctional terminal (the cursor up and down keysor the volume key).・Whether the functions mentioned above work or not depends on the destination system. For moredetails, refer to the manual that comes with the destination system.・The ways you originate calls from the Bluetooth ® headset and answer terminating calls may varydepending on the type of device you use.A50-013692-002Issue 2.02008.7IP3NA-BHA ADAPTER Connection ManualIP3NA-BHA ADAPTERBluetooth compatibleheadsetRCaution