NOBOCOOL Oslo Series Quick Start Manual
Programmable Timerfor NTE4T SeriesSet current day and timeEnter “settings” menu Press bottom left button to select “set day/time” menuThe day function should be flashing.1. Select day by pressing up or down arrow.2. Press bottom left button to confirm day.Now do the same to select and confirm hour and minute of current time.NB: Time is in 24 hour format.Quick Start guideThis instruction manual will show you how to use the timer on the heater. If you do not want touse the timer, please simply skip to the “Set current day and time” section to learn how to inputthe time. You can control the thermostat with the up and down buttons and turn the heater onand off with the switch on the side of the heater.timer OverviewThe timer has two heat modes: one for“day/peak” and one for “night/off peak”.You can set a different temperature forboth of these periods, for example,to keep the room warm during theday while you are using it and then totake the chill off the room when youare sleeping.The desired temperature for each heatmode can be set to between 7°C and30°C. Alternatively, you can just have theheater turn off in either mode.The icon in the bottom left of the screen(either a sun or moon symbol) will denotethe current heat mode (either day/peakor night/off-peak).Sometimes, you may want to switch your current heat mode (from the default mode set for the current time) to thenon-current mode e.g. from day/peak to night/off-peak or vice versa.You may want to do this to allow you to adjust the desired temperature/thermostat of the non-current mode.Or you may want to apply the other heat mode at this current moment (e.g. you may want to turn up the temperaturetemporarily without distorting the pre-programmed settings)To manually switch heat modes (e.g. from night/off-peak to day/peak or vice versa), simply press the top left buttonnext to the picture of either the sun or the moon. That icon should now get highlighted with a black background andthe desired temperature in the display screen should also change (assuming the alternative heat mode has a differenttemperature).In the diagram shown, the desired temperature/thermostat has changed from 21 (set for day/peak mode) to 16 degrees(set for night/off peak mode).Press the same button again to go back to the default heat mode for the current time.Note: for safety reasons, at 3am each day, if the heat mode has been manually overridden, the heater will automaticallyswitch back to the default heat mode for that time. Manual overrides will also end when a new timing setting starts.To lock the timer (e.g. so children cannot change the settings), press and hold the two left buttons for onesecond. A lock icon should show up on the right side of the display screen.To unlock the timer, again press and hold the two left buttons for one second. The lock icon should disappearand the regular settings should reappear on the display screen.Manually Overriding Heat ModesHeater on lightkey LockThis light will illuminate when theheating element is on.glen dimplex australia Pty LtdUnit 1, 21 Lionel RoadMount Waverley VIC 3149Ph: 1300 556 816 Fax: 1800 058 900Email: sales@glendimplex.com.auwww.nobo.com.auglen dimplex New Zealand Ltd38 Harris RoadEast Tamaki, AucklandPh: 09 274 8265 Fax: 09 274 8472Email: sales@glendimplex.co.nzwww.nobo.co.nzSelects the function shown in the top right ofthe display screen. In many menus, this buttonwill take you back to the previous screen.Scroll down/decreaseScroll up/increaseDesiredtemperaturefor currentheat modePress top left button tomanually override thecurrent heat mode –see “Manual OverrideHeat Mode” sectionCurrent dayand timeCurrent heatmode is“day/peak”Selects the function shown in the bottom rightof the display screen. In many menus, thisbutton will confirm your settings.page 1Oslo Range |
Related manuals for NOBOCOOL NTE4T Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine