Namron ZIGBEE DIMMER TW 400W Manual
     |
Function introductionImportant: Read All Instructions Prior to Installation• DO NOT install with power applied to device.• DO NOT expose the device to moisture.Safety & Warnings“Reset” Key: fornetwork pairing,touchlink, factoryreset of the dimmer,turn on/off loadOperationAC 100-240V power inputMin.SetLL NNOUTLNAC 100-240VLoad output• ZigBee AC phase cut tunable white dimmer based on latest ZigBee 3.0 protocol• 100-240VAC Wide Input and Output Voltage• Mini size, easy to be Installed into a standard wall box• 1 Channel Output, Up to 400W• Input and Output with Screw Terminals, Safe and Reliable• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator• Supports self-forming zigbee network without coordinator and add other devices to the network• Supports resistive loads and capacitive loads• Supports find and bind mode to bind a ZigBee remote• Compatible with universal ZigBee gateway products• Radio Frequency : 2.4GHz• Both leading edge version and trailing edge version are available for choosing, default factory setting is trailing edge• Enables to control color temperature, light intensity, ON/OFF of phase cut dimming tunable white LED drivers or lamps• ZigBee end device that supports Touchlink commissioning• Can be controlled by universal push switches• Waterproof grade: IP20• Supports zigbee green power and can bind max. 20 zigbee green power remotesResetInput Voltage Output Voltage Output CurrentProduct DataSize(LxWxH)Compatible Load TypesLoad Symbol Load Type Maximum Load RemarksDue to variety of LED lampdesigns, maximum numberof LED lamps is furtherdependent on power factorresult when connected todimmer.Maximum permitted numberof drivers is 200W dividedby driver nameplate powerrating.Dimmable LED lampsDimmable LED driversIncandescent lighting,HV Halogen lampsLow voltage halogenlighting with electronictransformers100-240VAC 1.8A max100-240VAC 45.5x45x20.3mm100W @ 110V200W @ 220V200W @ 220V100W @ 110V200W @ 110V400W @ 220V100W @ 110V200W @ 220V1.Do wiring according to connection diagram correctly.3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing willfail. Please refer to the part "Factory Reset Manually".Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode asinstructed by the controller.Step 3: power on the device, it will beset into network pairing mode(connected light flashes twice slowly),the network pairing mode will last untilthe device is added to a zigbeenetwork.Step 4: Connected light will blink 5times and then stay solid on, then thedevice will appear in your controller'smenu and can be controlled throughcontroller or hub interface.Input Clusters• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes• 0x0006: On/off • 0x0008: Level Control • 0x0300: Color Control • 0x0b05: DiagnosticsOutput Clusters• 0x0019: OTAZigBee Clusters the device supports are as follows:2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. Thisreceiver receives and is controlled by wireless radio signals from the compatible ZigBee system.LNAllowed Inrush CurrentCold Start 75A max.“Min. Set” Key:1) to set or delete a minimumdimming level2) to set or delete a startupbrightness levelS1COMPush switch inputMin.SetLL NNOUTLNAC 100-240VResetS1COM |
Related manuals for Namron ZIGBEE DIMMER TW 400W
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine