Namron ZigBee Quick Start Manual
   |
NAMRON DIY ZigBee RGBW LED Controller 09.ZGDIYRGBW.04282Function introductionImportant: Read All Instructions Prior to Installation12VDC InputCommon Anode output (+)• DO NOT install with power applied to device.• DO NOT expose the device to moisture.Product DataSafety & WarningsInput Voltage Output TypeOutput Current12/24VDC Constant voltage72W@12V, 144W@24V4CH, 1.5A/CHOutput PowerNo.1Dimension (LxWxH)84x20x14mmCH 3 (B) output (-)CH 2 (G) output (-)CH 1 (R) output (-)CH 4 (W) output (-)• Mini size zigbee RGBW LED light device based on latest ZigBee 3.0 protocol• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights• ZigBee end device that supports Touchlink commissioning• Supports find and bind mode to bind a ZigBee remote• Compatible with universal ZigBee gateway products• Waterproof grade: IP20• W channel can be controlled through Gateway’s color temperature control interface• W channel can be controlled separately from RGB channels through RGBW zigbee remote or touchpanel’s W button• Supports self-forming zigbee network without coordinator• Supports zigbee green power and can bind max. 20 zigbee green power remotesOperation1.Do wiring according to connection diagram correctly.2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatiblesystems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBeesystem.3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)4. TouchLink to a Zigbee Remote< 10cmNote: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.4) After TouchLink, the device can be controlled by the linked remotes.V+ V+R- R-G- G-W- W-B- B-ZigbeeRemoteStep 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing willfail. Please refer to the part "Factory Reset Manually".Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode asinstructed by the controller.Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15minutes timeout, repeat the operation.Step 1: Method 1: Re-power on the device 4 times to start Touchlink commissioning immediately, 180S timeout,repeat the operation.Method 2: Re-power on the device, Touchlink commissioning will start after 15 if it’s not added to azigbee network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Oncetimeout, repeat the operation.minutesStep 2: Bring the remote or touch panel within 10cm of the lighting device.Step 3: Set the remote or touch panel into Touchlink commissioning,please refer to corresponding remote or touch panel manual to learn how.Step 4: Connected light will blink 5 timesand then stay solid on, then the devicewill appear in your controller's menu andcan be controlled through controller orhub interface.Step 4: There shall beindication on theremote for successfullink and connectedlight will flash twice.5. Removed from a Zigbee Network through Coordinator or Hub InterfaceFrom your ZigBee controller or hub interface, choose to delete or reset thelighting device as instructed. The connected light blinks 3 times to indicatesuccessful reset.AC Power50/60HzLNGV+V-OUTPUTINPUT12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-Input Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-AC Power50/60HzLNGV+V-OUTPUTINPUT12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-V+ V+R- R-G- G-W- W-B- B-Note: 1) W channel can be turned on through Gateway’s color temperature control interface which will mix RGBchannels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, thebrightness of white channel will be controlled together with RGB channels.2) W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’sW button, please refer to their manuals. |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine