Navman Smart Box II User Manual
  |
User ManualSmart Box IIRevision: R00(1/2019)TrademarksAll brand and product names are trademarks or registered trademarks of their respective companies.DisclaimerSpecifications and documents are subject to change without notice. Navman does not warrant this documentis error-free. Navman assumes no liability for damage incurred directly or indirectly from errors, omissions, ordiscrepancies between the device and the documents.NotesNot all models are available in all regions.Depending upon the specific model purchased, the colour and look of your device and accessories may not exactlymatch the graphics shown in this document.Regulatory informationFor regulatory identification purposes, this product is assigned a model number of N467. Marking labels located onthe exterior of your device indicate the regulations that your model complies with. Please check the marking labelson your device and refer to the corresponding statements in this section. Some notices apply to specific modelsonly. The user needs to switch off the device when exposed to areas with potentially explosive atmospheres suchas petrol stations, chemical storage depots and blasting operations.WEEEThis product must not be disposed of as normal household waste,in accordance with the EU directive for waste electrical andelectronic equipment (WEEE – 2012/19/EU). Instead, it shouldbe disposed of by returning it to the point of sale, or to a municipalrecycling collection point. 5 6 1 5 N 5 8 3 0 0 0 9 R 0 0IntroductionNavman Smart Box II provides power to your Navman dash cam by connecting with the constant power of the fuseterminal of your vehicle. It is very useful when you want to record video footage whilst parking. The Smart Box IIcan prevent the discharge of the vehicle battery by blocking the electric power automatically as it checks the presettime and voltage.Parts and functions1 Fuse cable- ACC (red wire)- B+ (yellow wire)- GND (black wire)2 Main unit of Smart Box II- Time and voltage setting switches- LED indicator3 Mini-USB connectorConnects to the recorder.Time and voltage setting switches Switch 1 and 2: Voltage setting switches Switch 3 and 4: Time setting switches1 ON / 2 ON11.8V23.6VPassenger car/RV:Truck/bus:1 OFF / 2 ON12.0V24.0V1 ON / 2 OFF12.2V24.4V1 OFF / 2 OFF11.6V23.2V3 ON / 4 ON12 hours3 OFF / 4 ON24 hours3 ON / 4 OFF36 hours3 OFF / 4 OFFPower offPrecautions and noticesRated input voltage: DC 12 - 24V, output current: 2A maximumWARNING! Do not use other than rated output voltage status. This product can only be used with the vehicles thathave DC 12 - 24V voltage. (Passenger car and RV: 12V; truck and bus: 24V)l Follow the installation instructions or ask a specialist technician for assistance.l There may be deviations in vehicle power voltages about vehicle battery status and usage environments. Makesure to turn off to the dash cam if the vehicle will not be used for 2 days or more.l Never attempt to disassemble, repair or make any modifications to the product. Disassembling, modifying orany attempt to repair could cause damage to your device, may inflict bodily harm or damage to property and willvoid any warranty.l You must use the product as intended. Misuses, neglect, accident or abuse will not cover the warranty,replacement or refund.l Do not drop the product or subject it to severe shock.l When installing, mounting and storing, please do so in a dry place.l Please check the installation and operation of the product regularly.l The manufacturer is not responsible for any damages caused by not observing the above warnings andprecautions.Installation and setup1. Set up the voltage and time by adjusting the switches.l Setting up the voltage: The Smart Box II is designed to power the dash cam by drawing power from the car'sbattery until it reaches a specific voltage limit. Once the car's battery falls lower than this level, the Smart BoxII will automatically stop drawing power from the car's battery.It is recommended to set the Smart Box II to 12.2V (for passenger car and RV) / 24.4V (fortruck and bus), and only change it to the other setting options after checking with your car'smanufacturer and/or car’s battery manufacturer. Please contact your car's manufacturer and/or car’s battery manufacturer for more information relating to the minimum battery voltagerequired for your vehicle.l Setting up the time: If the time passes the preset time (by checking the time after vehicle ignition is turnedoff), the power to the dash cam will be disconnected automatically.l Select either 12 / 24 / 36 hours to enable the uninterrupted power function of the Smart Box II and thedash cam will be powered even when the vehicle engine stops.l If Power off is selected, the uninterrupted power function of the Smart Box II will be disabled and the dashcam will be powered only when the vehicle engine is started.12 hours 24 hours 36 hours Power off2. Locate and open the fuse box inside of the vehicle.Please note that the installation illustrations are for your reference only. The placement of the fuse box mayvary depending on the vehicle model. If you encounter any problems during installation, it is recommendedthat you contact a skilled installer (e.g. the service personnel of the vehicle) for assistance.3. Check and confirm the vehicle's voltage by using the electricity tester as battery voltages varies by vehicle.You must confirm your vehicle's voltage.Use the electricity tester to locate the fuse from which the power is supplied even when the vehicle is turnedoff, such as the emergency flashing hazard lights, interior and door lights etc. Connect the yellow wire (B+) tothe fuse.Use the electricity tester to locate the fuse from which the power is not supplied when the vehicle is turned off,such as the indicator lights. Connect the red wire (ACC) to the fuse.The black wire (GND) must be connected to the metal part of the vehicle for grounding. If not grounded, thisproduct may not work properly. You can use a screw to attach the black wire to the vehicle (try to find a screwhole on any metal part).Connect the Smart Box II to the dash cam and confirm it is working properly by the LED indicator that glows inred. Then you can arrange the cable and complete the installation.The length of the provided cable is about 4.5 metres. You can route the cable through the top ceiling and theA-pillar so that it does not interfere with driving. Make sure that the cable installation does not interfere withthe vehicle airbags or other safety features. |
Related manuals for Navman Smart Box II
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine