Netopia 3-D Reach 3300 Series Quick Start Manual
  | |
Contents | 
Netopia® 3-D Reach ™Wi-Fi GatewaysMMMMooooddddeeeellllssss:::: •••• Netopia® 3300-Series ADSL 3-D Reach™ Wi-Fi Gateways•••• Netopia® 3300-Series Broadband 3-D Reach™ Wi-Fi GatewaysQuickstart GuideUnpack your Gateway, check your package contents, and decide on a location. Consider:• Place the Gateway in a spot that is easily accessible for you. You can lay it flat or mounton the wall.• Keep the cables away from other electrical devices that may interfere with the operationof your Gateway.If you don’t have everything, contact your supplier immediately.Note: Note the serial number (SN:) of your Gateway. It is located on the label on the bottom ofthe Gateway below the model number. You will need the Gateway’s serial number when installingwireless card(s) or adapters, or if you need to call for technical support.The Netopia Installation Wizard automates several tasks to get you up and running easily.You can run the Wizard on every WWWWiiiinnnnddddoooowwwwssss----bbbbaaaasssseeeedddd PPPPCCCC that will connect to your network,whether it is connected via Wireless, USB, or by Ethernet cable.>>>>BBBBeeee ssssuuuurrrreeee ttttoooo ddddiiiissssaaaabbbblllleeee ffffiiiirrrreeeewwwwaaaallllllll pppprrrroooodddduuuuccccttttssss ssssuuuucccchhhh aaaassss NNNNoooorrrrttttoooonnnn PPPPeeeerrrrssssoooonnnnaaaallll FFFFiiiirrrreeeewwwwaaaallllllll oooorrrrMMMMccccAAAAffffeeeeeeee PPPPeeeerrrrssssoooonnnnaaaallll FFFFiiiirrrreeeewwwwaaaallllllll bbbbeeeeffffoooorrrreeee rrrruuuunnnnnnnniiiinnnngggg tttthhhheeee wwwwiiiizzzzaaaarrrrdddd....<<<<1.IIIInnnnsssseeeerrrrtttt tttthhhheeee CCCCDDDD iiiinnnnttttoooo yyyyoooouuuurrrr CCCCDDDDRRRROOOOMMMM ddddrrrriiiivvvveeee.... The Installation Wizard will runautomatically and step through your connection installation(s).2.When prompted, connect a PC to any of the Ethernet “LAN” ports using theYellow RJ-45 Ethernet cable. Use additional standard Category 5 Ethernet cables(not supplied) to connect up to four devices.3.If you are installing a Netopia 3-D Reach Wireless card, use the NetopiaInstallation Wizard on your laptop or PC. If you are using third-party,non-Netopia-supplied wireless adapters with your Gateway use the drivers/CDthat are compatible for that wireless adapter.When all of your connections are made, your network may look like this:When all of your connections are made, the status LEDs on the front of your Netopia Gatewaywill light, according to the following diagram:ChecklistNetopia Gateway CD & Quickstart GuidePowerSupplyLavender RJ-11Telephone CableorGray RJ-45Modem CableYellow RJ-45EthernetCable-or-Use the Netopia Installation WizardThe Welcome screen lists the tasks thatyou can perform with the Netopia Installa-tion Wizard.The second screen lets you choose whichtype of Netopia device you are installing,and where you are installing it.Once you make your choice, subsequentscreens will install the appropriate drivers,if required, and perform configurationtasks, depending on the type of device youare installing.Follow the on-screen instructions.Power Off / OnLANModem4 123DSL or Cable DC PowerRear ViewModemModem Port(Ethernet models)EthernetPortsPower SwitchDSL Port(DSL models)11For Ethernet models, connect to DSL or Cable modem;For DSL models, connect directly to DSL wall outletModemPower -Ethernet 1, 2, 3, 4 - Modem (Ethernet models) -Flash green when there isactivity on the LAN.Front ViewFlashes green for activityon the modem port.Solid green when connected. Solid green when connected.Green when power is on.Wireless -Flashes green when there isactivity on the wireless LAN.Flashes green when trainingSolid green when trainedDSL Sync (DSL models) -– OR –1 2 3BROADBAND WITHOUT BOUNDARIES ™ |
Related manuals for Netopia 3-D Reach 3300 Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine