Netopia 3346(EU Quick Start Manual

Contents

quickstart guide

Netopia 3346(EU Quick Start Manual Manual pdf 1 page image

Netopia® 4-Port ADSL RouterMMMMooooddddeeeellllssss:::: Netopia® 3346(EU, DE)-ENT / 3356(EU, DE)-ENT ADSL Routers – All ModelsQuickstart GuideUnpack your Gateway, check your package contents, and decide on a location:• Place the Gateway in a spot that is easily accessible for you. You can lay it flat ormount on the wall.• Keep the cables away from other electrical devices that may interfere with the oper-ation of your Gateway.If you don’t have everything, contact your supplier immediately.1. After unpacking your Netopia Router shipping carton, decide where you wantto locate the Router.You should install the Router near your PC or another location that permits easy accessand visibility. You can lay the Netopia Router flat or mount it on a wall. Make sure anyEthernet cables are kept away from power cords, fluorescent lighting fixtures, andother sources of electrical interference. Put the Router in a location where air can circu-late freely around it.2.Connect the power transformer to the power jack on the Router back panel.Plug the power transformer into an appropriate electrical outlet.Turn on the power with the power switch. The Power light should come on solid green.3.Connect the Router to the wall jack that supports your DSL service.Insert one end of the lavender telephone cable in the DSL port on the Router backpanel until you feel it lock. Insert the other end of the telephone cable into the tele-phone jack connected to your ADSL service. The DSL SYNC indicator light shouldblink for up to two minutes and then come on solid green.4.Connect the Router to create your Ethernet local area network (LAN.)Connect the yellow Ethernet cable to your first PC and to the Router.The LAN indicator light should come on solid green for the port where you connectedyour Ethernet cable.Connect each computer or other device to a switch port on the back of the Router withan Ethernet cable (maximum length 100 meters). If you need more than four ports, con-nect a hub or switch to the Router using a standard Ethernet cable.When all of your connections are made, the status LEDs on the front of your Netopia Routerwill light, according to the following diagram:The following instructions assume that you want to use the automatic configuration andaddress sharing features of the Router to provide IP information to devices on your localEthernet network.1. Configure your computer to use an IP address on the same TCP/IP network asthe Netopia Router.• Windows 95/98 or Windows ME:• Right-Click on the NNNNeeeettttwwwwoooorrrrkkkk NNNNeeeeiiiigggghhhhbbbboooorrrrhhhhoooooooodddd icon on your Windows desktop andselect PPPPrrrrooooppppeeeerrrrttttiiiieeeessss from the pull-down menu.• In the list of network components, highlight the entry that says“TTTTCCCCPPPP////IIIIPPPP (((([[[[yyyyoooouuuurrrr EEEEtttthhhheeeerrrrnnnneeeetttt ccccaaaarrrrdddd hhhheeeerrrreeee]]]])))) ”.• Click the PPPPrrrrooooppppeeeerrrrttttiiiieeeessss button.• Click the OOOObbbbttttaaaaiiiinnnn aaaannnn IIIIPPPP aaaaddddddddrrrreeeessssssss aaaauuuuttttoooommmmaaaattttiiiiccccaaaallllllllyyyy radio button. Click the DNS Con-figuration tab. Click the DDDDiiiissssaaaabbbblllleeee DDDDNNNNSSSS radio button. Click the Gateway tab and removeany installed Gateways. Click the OOOOKKKK button twice. When prompted, restart your PC.• Proceed to the next section “Configure Your Netopia Router”.• Windows 2000 and XP• Right-Click on the MMMMyyyy NNNNeeeettttwwwwoooorrrrkkkk PPPPllllaaaacccceeeessss icon on your Windows desktop and selectPPPPrrrrooooppppeeeerrrrttttiiiieeeessss .• Select your LLLLooooccccaaaallll AAAArrrreeeeaaaa CCCCoooonnnnnnnneeeeccccttttiiiioooonnnn .• Right click on your LLLLooooccccaaaallll AAAArrrreeeeaaaa CCCCoooonnnnnnnneeeeccccttttiiiioooonnnn and select PPPPrrrrooooppppeeeerrrrttttiiiieeeessss .• Select IIIInnnntttteeeerrrrnnnneeeetttt PPPPrrrroooottttooooccccoooollll [[[[TTTTCCCCPPPP////IIIIPPPP]]]] .• Click the PPPPrrrrooooppppeeeerrrrttttiiiieeeessss button.• Click the OOOObbbbttttaaaaiiiinnnn IIIIPPPP aaaaddddddddrrrreeeessssssss aaaauuuuttttoooommmmaaaattttiiiiccccaaaallllllllyyyy radio button and the OOOObbbbttttaaaaiiiinnnn DDDDNNNNSSSSsssseeeerrrrvvvveeeerrrr aaaaddddddddrrrreeeessssssss aaaauuuuttttoooommmmaaaattttiiiiccccaaaallllllllyyyy radio button. Click the OOOOKKKK button.• Proceed to the next section “Configure Your Netopia Router”.ChecklistNetopia Router CD & QuickstartGuidePower SupplyLavender RJ-11Telephone Cable Yellow RJ-45Ethernet CableLAN 1LAN 2LAN 3LAN 4DSL SYNCPower-or-North AmericanInternationalSet up your RouterDSL 10/100BT LAN Power SupplyPower Off / OnLANDSL4 123Power Switch234Rear ViewConfigure Your PC for Dynamic AddressingLAN 1LAN 2LAN 3LAN 4DSL SYNCPowerPower - Green when power is appliedFlashes green when trainingSolid green when connectedSolid green when trainedto each port on the LAN.LAN 1, 2, 3, 4 -DSL SYNC -Flash green when there isactivity on each port.Flashes green for DSL trafficFront View1 2 3BROADBAND WITHOUT BOUNDARIES ™

/ 2

Related manuals for Netopia 3346(EU