Netopia TER/ATA-N1 Quick Start Manual
Also see for TER/ATA-N1: User guide
  | |
Contents | 
Netopia VoIP ATAQuickstart GuideVoIP ATA Package Contents ChecklistFor any missing items, please contact your dealer immediately.Top View:Rear Panel:Typical VoIP ATA ConnectionADSL Connection Diagram Cable Connection DiagramFor a Company Network ConnectionUDP port 5060 for SIP Signaling and UDP ports 5000-5020 for RTP must be open.Netopia VoIP ATA CD & QuickstartGuidePowerSupplyGray RJ-11TelephoneCableGray RJ-45EthernetCableIIIIMMMMPPPPOOOORRRRTTTTAAAANNNNTTTT SSSSAAAAFFFFEEEETTTTYYYY IIIINNNNSSSSTTTTRRRRUUUUCCCCTTTTIIIIOOOONNNNSSSS –––– PPPPOOOOWWWWEEEERRRR SSSSUUUUPPPPPPPPLLLLYYYY IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNNConnect the power supply cord to the power jack on the Netopia ATA. Plug thepower supply into an appropriate electrical outlet.CAUTION:Depending on the power supply provided with the product, either the direct plug-in power supply blades, power supply cord plug or the appliance coupler servesas the main power disconnect. It is important that the direct plug-in power supply,socket-outlet or appliance coupler be located so it is readily accessible.(Sweden) Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk(Norway) Apparatet må kun tilkoples jordet stikkontakt.TTTTEEEELLLLEEEECCCCOOOOMMMMMMMMUUUUNNNNIIIICCCCAAAATTTTIIIIOOOONNNN IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNNWhen using your telephone equipment, basic safety precautions should always befollowed to reduce the risk of fire, electric shock and injury to persons, includingthe following:• Do not use this product near water, for example, near a bathtub, wash bowl,kitchen sink or laundry tub, in a wet basement or near a swimming pool.• Avoid using a telephone (other than a cordless type) during an electrical storm.There may be a remote risk of electrical shock from lightning.• Do not use the telephone to report a gas leak in the vicinity of the leak.SSSSAAAAVVVVEEEE TTTTHHHHEEEESSSSEEEE IIIINNNNSSSSTTTTRRRRUUUUCCCCTTTTIIIIOOOONNNNSSSSLED STATUS DESCRIPTIONSPOWER On The VoIP ATA is receiving power.ETHERNETOn The VoIP ATA has an Ethernet connection with a cableor DSL modem or network.Blinking The VoIP ATA is sending/receiving data to/from thecable/DSL modem or network.Off The VoIP ATA doesn't have an Ethernet connection withthe cable/DSL modem or network.PHONEOn This port is registered to the Internet Phone ServiceProvider.Blinking The telephone(s) connected to this(these) port(s)is(are) off-hook.Off This port is not registered to an Internet Phone ServiceProvider.DESCRIPTIONSPOWER This is where the included power adapter is connected.MODEM This port allows connection of the VoIP ATA to a router, gateway or net-work using a Category 5 (or better) Ethernet network cable (RJ-45).ETHERNET SWITCH PHONE LINERESETPress and hold the RESET button for 2 to 4 seconds to restore the VoIPATA's WAN Static IP to 192.168.1.200 while keeping all the other settingsintact.Press and hold the RESET button for more than 5 seconds to restore theVoIP ATA to default factory settings.PHONE The PHONE port allows you to connect your telephone to the VoIP ATAusing an RJ-11 telephone cable.B ROADBAND WITHOUT BOUNDARIES ™ |
Related manuals for Netopia TER/ATA-N1
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine