Nidac PROVE BDF43C Quick Start Manual
®BDF43C & BDF62CDual Frequency Card Reader & KeypadFEATURES• Compatible with all NIDAC Presco and Prescient controllers• Outputs Presco and Wiegand data• Site code read from EM cards in Wiegand mode is compatible with genericEM Wiegand prox readers• Reads HID 125kHz cards• Fully configurable for custom Wiegand keypad modes• Reads Mifare S50 CSNs• Suitable for indoor or outdoor use• Audible and visual (buzzer & LED) feedback of each key pressed and cardread• 12-24V DC operation• Operating temperature range of -20ºC to 70ºC• 5 year manufacturer’s warranty• Tested to IP65IMPORTANT NOTICES FOR PRODUCT• Note that the default reading behaviour will preferentially read LFcredentials over HF when both are presented• Standard 26 & 37 bit HID cards can be read, other HID formats will readbut the output of some cards may not match that of an HID reader.INSTALLATION1. Use the mounting plate to mark the installation location2. Install the mounting plate using at least two screws in either the top andbottom or left and right (BDF43C only) slots on the mounting plate3. Attach cable plug and then slide the BDF-C into place4. Insert one of the supplied counter-sunk M3 Phillips head or allen key screwsto secure the keypad to the mounting plateSPECIFICATIONSVoltage: 9V to 28V D.C.Current: 200mA max.Operating Temp: -20C to 70C.Weight: BDF-43C: 185g, BDF-62C: 130gDimensions: BDF-43C: 80mm (W) x 130mm (H) x 25mm (D)BDF-62C: 45mm (W) x 136mm (H) x 25mm (D)Read Range: LF: Up to 20cm (8”). HF: Up to 2cm.Keypad Output: Presco DTA, Wiegand (up to 64 bit) or burst mode.Prox Output: Presco DTA or Wiegand.Wiegand Output: Pulse width = 50s, pulse separation = 2ms.Wiring Distance: BDF-C to Presco PAC controller = 1Km using unshieldedcable, 100 max. return resistance on DTA line. To achievedistances greater than 100m the BDF-C may require aseparate local power supply depending upon the thickness ofthe cable used.BDF-C to Wiegand controller, shielded cable must be used.Wire Gauge Distance Wire Gauge Distance22 AWG 150m (490 ft) 26 AWG 60m (195 ft)24 AWG 100m (330 ft) 28 AWG 40m (130 ft)WIRESThere are 8 wires for the BDF-C, not all will be needed for each installation. Theunused wires should always be terminated and left unconnected.Black 0V (Ground).Red +12V D.C.White DTA (Presco data line) or D1 (Wiegand Data 1).Green D0 (Wiegand Data 0).Blue Blue LED control wire, +3V to +14V active.Yellow Blue LED control wire, 0V active.Brown Buzzer control wire, 0V active.Orange Tamper / open collector outputBDF-C TO PAC1 / PAC2Programming Prox cards & tags into a PAC controllerTo program a proximity card or tag into a PAC controller follow the same stepsas shown in the controller manual for programming a new user code. When itcomes to the stage to enter the user code simply present the card or tag to theBDF-C, or alternatively enter the 9 digit code for the proximity card, note that thiscode may contain star (*) and hash (#) symbols and leading zeroes (0) do needto be entered.PAC1 Programming ExampleThis example uses a PAC1 controller, programming a momentary operationproximity card or tag into memory location 001.1. Put the PAC1 into program mode using the management code or button onthe PAC12. Use the keypad on the BDF-C to open the memory location to store the Proxcard in * 001 1 #3. Present the proximity card or tag to the BDF-C4. Take the PAC1 controller out of program modeUSING THE BDF-C WITH WIEGANDThe BDF-C can be used with any standard Wiegand and most non-standardWiegand controllers. The site (facility) code for the keypad can be set from thekeypad itself (refer to the Wiegand Keypad Options section) and the Wieganddata is fully configurable with up to 64 bits of data. The BDF-C also supportscontrollers that require burst mode format Wiegand.To use the BDF-C in non burst Wiegand mode, press the code then key. TheBDF-C can be set up to automatically send the code after a given number of keypresses by setting memory 007 (refer to the General Options section).BDF-C TO WIEGANDTo change the status LED colour from violet to green apply a negative signal (0to 2V) to the Yellow wire or a positive signal (2.5 to 28V) to the Blue wire.To sound the buzzer, apply a negative signal (0 to 2V) to the Brown wire.* If a fused output for readers is not provided use a 200mA inline fuse to protectthe power supply from short circuiting if BDF-C wires are tampered with.BDF-C OPTIONSThere are several options that can be set to alter the way in which the BDF-Cbehaves. These options fall into the 4 categories of General, Presco, WiegandKeypad and Wiegand EM Card Proximity Reader, all of these are explainedbelow.General OptionsThese options set the functionality of the BDF-C independent of whether it is inWiegand or Presco mode and the HF & LF global reader options.Memory Function Default005 Force Presco or Wiegand mode (1) 255006 Key press timeout in seconds 10007 Auto send key count (2) 0080 LF & HF Read Options (3) 10081 HF Mifare CSN Wiegand read option (4) 10(1) - Force Presco or Wiegand mode [Memory 005]101 = Always in Presco mode.202 = Always in Wiegand mode.All other values = Mode auto detected using white wire. |
Related manuals for Nidac PROVE BDF43C
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine