NightStick FDL-300R-K01 Instruction Manual

Also see for FDL-300R-K01: Instruction manual

NightStick FDL-300R-K01 Instruction Manual Manual pdf 1 page image

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-FDL-300R-K01-18PACKAGE CONTENTS• 1 – FDL-300R Tactical Fire Light• 1 – NS-HMC1 Multi-Angle Helmet Mount• 2 – CR-123 Lithium Batteries• 1 – 5/16” - 18 x 1/4” Light Mounting Allen Set Screw (installed in mount)• 2 – 5/16” - 18 x 1/4” Brim Mounting Allen Set Screws (installed in mount)– for Fire Helmets• 2 – 5/16” - 18 x 3/8” Brim Mounting Allen Set Screws (loose) – for Hard Hats• 1 – 5/32” Allen WrenchAPPLICATIONThe FDL-300R-K01 Tactical Fire Light w/ Multi-Angle Helmet Mount is acomplete system for attaching the Tactical Fire Light to any Fire Helmet orHard Hat.The Tactical Fire Light is rated at 180 Lumens and has a tight long-throwbeam that is distance rated at 190 meters. The light is IP-X7 waterproof andis drop rated at 2 meters.The Multi-Angle Helmet Mount can be attached to either side of virtuallyany Fire Helmet or Hard Hat and provides 140 degrees of adjustability. Thisadjustability allows the user to best position the light for purposes of providingclearance around face shields, goggles or other potential obstructions.INSTALLING BATTERIES INTO THE TACTICAL FIRE LIGHT• To install the included CR-123 Lithium Batteries in the Tactical Fire Light,begin by unscrewing and removing the tail-cap switch. (Image 1)• Insert both batteries into the handle of the light with the positive terminalends being inserted first. (Image 2)• Re-install the tail-cap switch, being careful not to cross-thread the tail-cap.(Image 3)• Tighten the tail-cap switch completely and then test the operation of thelight (see OPERATION below).INSTALLING THE LIGHT INTO THE MULTI-ANGLE MOUNTBegin by deciding which side of the helmet the FDL-300R-K01 TacticalFire Light w/ Multi-Angle Helmet Mount is to be attached. This will determinethe proper orientation of the light in the mount. Additionally check that thefi nal location on the helmet does not interfere with the normal operation offace shields, goggles, etc.• Remove the 5/16” - 18 x 1/4” Light Mounting Allen Set Screw from theMulti-Angle Helmet Mount and slip the Tactical Fire Light into the mount.(Image 4)• NOTE: The Multi-Angle Helmet Mount may be positioned anywherealong the length of the Tactical Fire Light. (Image 5)• Once the light is in the proper position, re-install the Light Mounting AllenSet Screw and tighten, securing the Tactical Fire Light in place. (Image 6)CAUTION: Be careful when tightening the Allen Set Screw. Do notover-tighten. Doing so may damage the handle of the light. The AllenSet Screw should only be tightened enough to prevent the light fromcoming loose. Over time this screw may come loose. Periodicallycheck and re-tighten as needed.SUGGESTION: Application of a thread locking solution (such asLoctite® Threadlocker Blue) may be applied to secure the Allen Set Screw.Do not use the “red” version of this product as it is designed for a morepermanent installation and would make it diffi cult to remove the Allen SetScrew in the future.INSTALLING THE FDL-300R-K01 ON TO THE HELMETInstruction ManualFDL-300R-K01THANK YOU FOR SELECTING THE NIGHTSTICK FDL-300R-K01TACTICAL FIRE LIGHT W/ MULTI-ANGLE HELMET MOUNT!PLEASE SAVE THESE INSTRUCTIONSPlease read these instructions before using your Nightstick FDL-300R-K01 Tactical Fire Light w/ Multi-Angle Helmet Mount. They includeimportant assembly and operating instructions.Image 1 Image 2 Image 3Image 4 Image 5 Image 6Image 7 Image 8 Image 9

/ 4

Related manuals for NightStick FDL-300R-K01