NightStick Xtreme Lumens TWM-850 Instruction Manual

Also see for Xtreme Lumens TWM-350: Instruction manual

NightStick Xtreme Lumens TWM-850 Instruction Manual Manual pdf 1 page image

BEFORE ATTACHING, INSPECTING OR SERVICING THE TWMy Engage the safety on the firearm (if applicable).y Remove the magazine from the firearm (if applicable).y Open the action and visually and physically inspect the chamber to be sure it is empty.y Keep the barrel pointed in a safe direction at all times and never place your hand infront of the muzzle.WARNING: IT IS IMPERATIVE THAT SAFETY MEASURES BE EMPLOYED ATALL TIMES WHILE HANDLING A FIREARM.GENERAL SAFETY WARNINGSy NOT FOR USE ABOVE HAZARDOUS LOCATIONSy DO NOT use in explosive atmospheres, near fl ammable liquids, or where explosionproof lamps are required.y DO NOT use in the proximity of vehicles or equipment when there is a risk offl ammable liquids coming into contact with the flashlight.y DO NOT expose the batteries to water or salt water, or allow the batteries to get wet.y DO NOT store the batteries with metallic objects that may cause a short circuit.y Immediately discontinue use of the batteries if they emit an unusual smell, feel hot,change color, change shape or appear abnormal in any way.y Keep out of the reach of children.STEP 1. INSTALL THE BATTERIESImage 1 Image 2 Image 3y To install the included CR-123 Lithium Batteries in the TWM, begin by unscrewingthe screw on the battery compartment door. (Image 1) This screw is designed toremain in the battery compartment door once it has been unscrewed, do not attemptto remove it.y Insert both batteries into the battery compartment paying attention to the batteryorientation marking on the sides of the light near the battery compartment door. (Image 2)y Re-install the battery compartment screw by pressing the door fully closed and thentightening the screw until it is hand tight. Do not over tighten. (Image 3)y Test the operation of the light (see OPERATION below).STEP 2. INSTALL THE LIGHT ONTO YOUR FIREARMThe TWM is designed to be easily attached and detached from the fi rearm’s tacticalrail. However, the fi rearm must have a tactical rail and it must have at least one cross railslot. The TWM is not designed to be used on a fi rearm that does not have a cross rail slot.IMPORTANT: Your TWM comes with the Universal Insert pre-installed in the slotlocation that will allow the light to fit on approximately 70% of the handguns on themarket today. If the fit is not correct for your specific handgun, use the included AllenWrench to relocate the Insert to the slot location that works best for your firearm.Image 4 Image 5 Image 6y Push inward on the head of the Rail Clamp Tension Thumbscrew to fully open theAdjustable Portion of the Rail Clamp. (Image 4)y While making sure that your fi rearm is in a safe condition and that the barrel is pointedin a safe direction, place the fi xed portion of the Rail Clamp into the groove of the tacticalrail on your fi rearm and align the Cross Rail Insert with the slot on your fi rearm.y Rotate the TWM onto the tactical rail (Image 5) and then release the pressure on theTension Thumbscrew making sure that the TWM is gripping both sides of the tacticalrail of your fi rearm and verify that the Cross Rail Insert is fully seated into the tacticalrail slot of your firearm. (Image 6)Instruction ManualTWM-350/850Please read these instructions before using your Nightstick TWM-350/850. Theyinclude important assembly and operating instructions.PACKAGE CONTENTSy 1 - Weapon Mounted Lighty 2 - CR-123 Lithium Batteriesy 2 - Cross Rail Inserts (1 pre-installed & 1 spare)y 4 - Cross Rail Mounting Cap Head Screws (2 pre-installed & 2 spare)y 1 - Allen WrenchWEAPON SAFETYPLEASE BE SURE TO READ, UNDERSTAND AND FOLLOW THESE SAFETYAND OPERATING INSTRUCTIONS WHEN HANDLING A FIREARM OR THENIGHTSTICK TWM WHEN MOUNTED ON A FIREARM. FAILURE TO DO SO CANBE DANGEROUS AND COULD RESULT IN SERIOUS INJURY, DAMAGE TOPROPERTY, OR DEATH.Use of a fi rearm under any circumstance is inherently dangerous. SERIOUSINJURY OR EVEN DEATH may result without proper training in the safe handling offi rearms. Proper training should be obtained from an accredited fi rearms safety programconducted by a qualified instructor.Read, understand and follow all of the safety instructions that came with your fi rearmbefore attaching your new TWM.y Always assume every firearm is loaded and treat that firearm as such.y Never point a firearm at anything that you are not willing to destroy.y Never service your fi rearm or your TWM when mounted on a fi rearm without fi rstactivating the weapon’s safety (if applicable), removing the magazine, opening theaction and physically and visually inspecting to make sure that no ammunition isinstalled in the firearm.WEAPON MOUNTED LIGHT SAFETYy Nightstick recommends that the TWM should only be activated with the non-triggerhand (support hand) while employing a two-hand grip on the fi rearm and with thetrigger finger fully outside the trigger guard when applicable.WARNING: FAILURE TO DO SO COULD RESULT IN AN ACCIDENTAL DISCHARGEAND SERIOUS INJURY, DAMAGE TO PROPERTY, OR DEATH.y Thoroughly practice (employing safe training conditions) with the TWM and anunloaded firearm before using the weapon.