Niigata seiki DMS-AE Instruction Manual

Niigata seiki DMS-AE Instruction Manual Manual pdf 1 page image

DUROMETERTYPE-A0509080 2070 301060 40DUROMETERTYPE-A0509080 2070 301060 40Throughout this manual, this mark :indicates a requirement, you MUST follow.Weight provides consistent measuring force.Handle for lowering Durometer to TestSample.Supports Weight. Please keep in properadjustment.With Gauge mounted, can be moved upand down.Platform for holding Test Sample.Screws for adjusting Test Sample tilt.Supports Test Stand.Tighten to secure the Bracket to the Post.Mounting for Durometer at bottom, supportsWeight at top.Support the Bracket.Holds the Weight to the Rod. Please keeptight and check periodically.Please use care and protect the TestPlatform from falling parts when workingwith the Rod assembly.Safety stop to prevent the Bracket fromfalling.Do not use to support Bracket; please makesure Bracket Clamp is tight whenpositioning Bracket.WeightHandleWeight Stop NutBracketTest PlatformAdjustment ScrewsBaseBracket ClampRodPostRod ScrewStop RingDMS-D onlyDUROMETER STANDHardness Tester - Measuring Jig DMS-AE DMS-DModel No.INSTRUCTION MANUALThank you for purchasing the Durometer Stand. Stand provides a constant measuring force when used with separatelyavailable Durometer to measure the hardness of plastic or rubber.For safe and proper operation, please read this instruction manual thoroughlybefore use and follow the procedures described. Please keep manual where it isaccessible to user for future reference.Keep this manual with the instrument if transferred or leased to a third party.For inquiries about our products, please contact dealer or place of purchase.SAFETY NOTICEPART IDENTIFICATION FUNCTIONBaseRodPostHandleWeightRod ScrewTest PlatformBracketWeight Stop NutAdjustmentScrewsBracketClampModel DMS-AE shown(Opposite Side)SAFETY PRECAUTIONS Please ObserveAlways follow the proper operating procedures in order to prevent harm to yourself or others, and to prevent damage to property.Improper use may cause injury or property damage.Read the instruction manual and follow theinstructions.Use of product other than as described in the manualmay cause accident.Use only as directed.This stand is to be used with separately availableDurometer as measurement jig for applying constantpressure when measuring hardness of plastic and rubber.Modification of product, or use other than as indicatedwill result in poor accuracy, component wear or damage,accident, or other unpredictable result.Use in an environment which meets the followingconditions:Dry location protected from rain, water, and oils.Location not subject to wide temperature changes.Location free from cutting chips and dust.Horizontal surface which is stable and free fromvibration.Location protected from use by children andunauthorized personnel.Use in location contrary to the above may cause poor accuracy,damage to the product, or may result in accident or injury.CAUTIONProduct only to be used with durometer modelslisted under Specifications section at end ofmanual.Weight is designed so that total weight will comply withJIS K6253 when used with specified durometer.Use of non-specified durometer will not be compliantwith JIS standard.Handle With Care.Do not drop or subject to shock - instrument accuracymay be affected.Insure hat Bracket Clamp is securely tightened.If Bracket Clamp is loose, measuring instrument maydrop causing damage or injury. Loose clamp will alsocause poor accuracy, damage, or malfunction.Follow instructions to apply rust preventivetreatment after use.Please refer to After Use Care, Storage section toprotect product from corrosion.Thumb Rest(Cap)TestSampleRodBracketTest PlatformDurometerMounting the Durometer Test Platform Slope AdjustmentSPECIFICATIONSMaterialsPost, Weight IronBase Cast IronTest PlatformGlassCompatible DurometerADM-A, ADM-EADM-DModel No.DMS-AEDMS-DWeight7.3kg11.4kgClean Test Platform with a soft, dry cloth moistened with alcohol.Do not clean with abrasive or stiff brush, as it will cause scratches and result in poor accuracy.Apply rust preventive oil to the Post and Weight.The Post and Weight are subject to corrosion, so please keep coated with oil and keep in low humidity environment.AFTER USE CARE, STORAGE NOTESRemove1Slowly Push DownAdjustHold HereWhile In ContactInstallWhile securely supporting the Bracket, loosen theBracket Clamp and move it up before re-tightening theclamp.For model DMS-D, adjust Stop Ring if required beforeloosening and adjusting the Bracket.Unscrew and remove the Thumb Rest from theDurometer.Insert the exposed thread of the Durometer into thehole at the bottom of the Rod and rotate to attach.(Make sure the Rod does not rotate while screwing onthe durometer by holding the Rod with your hand.)While securely supporting the Bracket, loosen the BracketClamp and adjust the height. The Duromter Indenter should beclose to the Test Platform without touching. When at properheight, secure by tightening the Bracket Clamp.Lower the Handle to move the Durometer into contact with theTest Platform.When Handle is fully depressed, do not apply additional force as thismay cause damage to the instrument.Monitor the Durometer Pointer as follows:With Handle down, adjust the two Platform AdjustmentScrews to adjust tilt until Pointer is within 1.Reading within 100 1 OK Reading more than 100 1 See stepOperationPlace the Test Sample on the Test Platform.While securely supporting the Bracket, loosen the Bracket Clamp andadjust the height until the Durometer Indenter is close to the Test Samplewithout touching. Tighten the Bracket Clamp to secure at the proper height.Slowly lower the handle.The Indenter should contact the Test Sample slowly, at a rate of less than3.2 mm/s for accurate measurement.With the handle down, wait the time period specified in the Test Procedureand then read the Gauge.When Handle is fully depressed, do not apply additional force as this maycause damage to the instrument.Gently raise the handle.Repeat for additional measurement points as specified by the DurometerTest Procedure.Please refer to Durometer Instruction Manual regarding Test Samples and Test Procedures.AdjustmentScrewsAdjustment ScrewsHandleStop RingDMS-D onlyNOTICE Test Platform can be easily damaged - please makesure the Platform is protected during assembly.Niigata seiki Co., Ltd.5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055Tel. : +81-256-33-5522 Fax. : +81-256-33-5518MAIL intl.sales@niigataseiki.co.jpURL http://www.niigataseiki.co.jp

/ 2

Related manuals for Niigata seiki DMS-AE