NiteRider Pro 3600 User Manual
Pro 3600Pro Series User Guide123100018003600Run Times*Settings6:003:301:30Pro 3600* Run times are approximations and will vary.DOWNLOAD PROGRAMS FROM THE D.I.Y. SOFTWARETo download Programs from the D.I.Y. Software, the DockingStation must be powered by a wall outlet, the Docking Station mustbe connected to the host computer and the headlamp must beconnected to the Docking Station.1. Plug the AC Adapter into the Docking Station and then intothe wall socket. The “Power” indicator on the docking stationwill illuminate solid red.2. Plug one end of the USB Cable into the Docking Station and theother end into the USB port of a computer. The “USB/PC”indicator will illuminate solid yellow.3. Connect the Pro 3600 headlamp to the Docking Station. The“Headlamp” indicator will illuminate solid yellow.4. Click the “Update” button on the D.I.Y. Software control panelto initiate transmission of Programs to the headlamp. Refer to the“D.I.Y. Pro LED Series Software Guide” for detailed informationon the software features and how they function.5. Both the “USB/PC” and “Headlamp” indicators will blinkindicating Programs are being downloaded through the DockingStation and into the headlamp.6. With a successful download, the headlamp LED indicatorchanges from red to green.Warning: Disconnecting the headlamp from the docking station,or the docking station from the computer, or disrupting powerto the docking station while transmitting Programs from theD.I.Y. Software will create a problem. The headlamp will eithernot operate or operate unpredictably. To correct this situation,disconnect power to the docking station, wait 10 seconds, thenreconnect power. The D.I.Y. Software and docking station willreconnect, then repeat the downloading process.D.I.Y. SOFTWAREThe latest version of the D.I.Y Software is available to download atwww.niteriderservices.com. The software runs under Windows 2000and above. For detailed information on the software please refer tothe “D.I.Y. Pro LED Series Software Guide”.RIDING AT NIGHTWhile a Pro 3600 lighting system will dramatically improve yourview, control and enjoyment of night riding, please remember thatcycling at night is an inherently dangerous activity. In addition tousing your lighting system properly and riding with extreme caution,NiteRider urges you to:• Never ride alone• Always let someone know where you are going• Wear a helmet and reflective clothing• Carry an auxiliary light and emergency supplies• Make sure the headlamp, mounting bracket and batteryare securely fastened.• Always disconnect the battery from the headlamp whentransporting the light system.PROTECTING YOUR INVESTMENTProperly charge your battery to maximize its lifespan (see the“Battery Charging and Care” section for detailed information). Whennot in use, always disconnect the headlamp from the battery tray.To unplug, grasp the connector, not the cable.The Pro 3600 will perform in wet weather conditions, butsubmerging it in water will damage the system.SUPPORTIf you experience difficulties during product installation or operation,NiteRider provides free telephone support on weekdays from 8:00AM to 4:30 PM (Pacific Time) at 800.466.8366, extension 4. Youmay also e-mail us at:NiteRider Technical Lighting Systems, Inc.8295 Aero Place, Suite 200San Diego, Ca 92123www.niterider.com@SupportniteriderdotcomFACTORY SETTINGSFactory settings are locked and cannot be changed. The Pro 3600factory settings include 3 light levels and the one flash pattern. Seetable below.THERMAL STEP DOWNIf the Pro 3600 headlamp is used in a static air environment, suchas bench testing, heat retention, due to inadequate airflow, maycause the light output to “step down” to a lower level to avoiddamage. In rare cases of extreme heat retention the light will powerof to protect the LED’s from overheating. Use a fan if bench testing thelight in a static air environment.DOCKING STATIONThe Docking Station has two uses.1. To recharge the Pro Series Li-Ion battery2. To download Programs from the D.I.Y Software to the headlampBATTERY CHARGING AND CAREBattery RechargingA Pro 3600 (8-cell, 7.4v, 11.6Ah, Li-Ion) will fully charge in 5:00 hours1. Plug the AC Adapter into the Docking Station and then intothe wall socket. The “Power” indicator on the docking stationwill illuminate solid red.2. Place the battery into the Docking Station. The “Battery”indicator will illuminate solid blue indicating contact and thatthe battery is ready to charge. A blinking yellow indicatorsignifies the battery is out of the permissible temperaturerange for charging.3. Status of the 5-step charging process is displayed on the frontpanel of the Docking Station.4. When the battery is fully charged the “Charged” indicator willilluminate solid green and charging will shut off automatically.5. Leaving the battery in the Docking Station indefinitely will notharm the battery. Every 24-hours the Docking Station will testthe battery level and apply a charge if required.Warning: If the “Batt Error” indicator illuminates solid red contactNiteRider Customer Service for assistance.150-22843 - Rev A |
Related manuals for NiteRider Pro 3600
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine