Nitecore TM16GT User Manual
  | |
Contents | 
Features· Utilizes 4 CREE XP-L HI V3 LEDs· Maximum output up to 3600 lumens· Features advanced temperature regulation (ATR) technology· Boasts a peak beam intensity of 252,000cd and a throw distance up to1003 meters· Dual-switch user interface ensures easy one-handed operation· Features 5 brightness levels and 3 special modes· High efficiency circuit board provides max runtime up to 610 hours· Integrated power indicator light displays remaining battery power(Chinese Patent: ZL201220057767.4)· Built-in power indicator displays battery voltage (accurate to 0.1V)· Direct access to ultra-low or turbo ensures flexibility and convenience· Reverse polarity protection prevents damage from incorrectly insertedbatteries· Rear tripod receptacle brings extra funtionality· Toughened ultra-clear mineral glass with anti-reflective coating· Constructed from aerograde aluminum alloy· Sturdy HAIII military grade hard-anodized· Waterproof in accordance with IPX-8 (two meters submersible)· Impact resistant to 1.5 meters· Tail stand capabilityDimensionsLength: 182mm (7.17”)Head diameter: 89mm (3.5”)Tube diameter: 53mm (2.09”)Weight521g (18.38oz)(without battery)Battery Options*Warning: Do not use the TM16 with RCR123 or CR123 batteries.Output & RuntimeNOTICE:The above data has been measured in accordance with the internationalflashlight testing standards ANSI/NEMA FL1 using 4 x 18650 (3.7V3400mAh) batteries under laboratory conditions. The data may varyslightly during real-world use due to battery type, individual usage habitsand environmental factors.Operating InstructionsBattery Installation1. Insert batteries with the positive (+) and negative (-) endscorresponding to the diagram on the inside of the battery compartment.2. Tighten the tailcap by aligning the two gold pins on the inside of thetailcap with the corresponding holes on the flashlight body, and rotateclockwise.User ManualThanks for purchasing NITECORE!®The All-Round Flashlight ExpertTURBO HIGH MID LOWLUMENS1500LUMENS3600 LUMENS500 LUMENS2101h 3h15minLOWERLUMENS5610h21h7h15min1,003m (Beam Distance)252,000cd (Peak Beam Intensity)IPX-8, 2m (Waterproof AND Submersible)1.5m (Impact Resistant)TM16GTAccessoriesLanyard, spare O-ringType Nominal voltage CompatiblePrimary Lithium battery CR123 3V NO18650 Rechargeable Li-ion battery 18650 3.7V Yes (Recommended)Rechargeable Li-ion battery RCR123 3.7V NONOTE: Upon battery installation, the power indicator light will blink toindicate the battery voltage. Please refer to the “Power Tips” section ofthis manual for details.WARNING:1. Do not mix batteries of different types/brands.2. When the TM16GT is stored in a backpack or left unused for extendedperiods, Nitecore recommends that batteries are removed to cut off thepower entirely, thus preventing battery drain or accidental activation ofthe flashlight.On/Off OperationTo turn on: press the on/off switch to turn the light on.To turn off: press the on/off switch again to turn the light off.Standby ModeWith the light turned on, press and hold the on/off switch for more thanone second to turn off the light and activate location indication. The bluepower indicator built in the side switches will blink once every threeseconds to indicate the location of the TM16GT. In this mode, theTM16GT will operate for approximately 6 months. With the powerindicator off in standby mode, the TM16GT can run for over 6 months.Brightness LevelsWith the light turned on, press the mode switch to cycle throughbrightness levels of lower, low, medium, high and turbo. The TM16GTmemorizes the brightness level last used when turned off, and enters thememorized brightness level directly upon next activation. |
Related manuals for Nitecore TM16GT
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine