Spray Height ControllerSummers(Main Lift & Enhanced Stability)Installation ManualSM03-4B

Introduction

Kit Part

Hydraulic Installation

Roll Sensor Installation

Electrical Installation

Software Setup

Cable Drawings

Norac UC5 Installation Manual

General UC5 System Layout

Ultrasonic Sensor Installation

CABLE UC5 INTERFACE TILT GP (WEATHERPACK)

CABLE UC5 INTERFACE MAIN GP (240")

CABLE UC5 BATTERY AMP

UC5 Topcon X30

list of parts

INSTALLATION

Pull Type

Switch Box Installation

CABLE DRAWINGS

ITEM C26: 43240-26 – Cable UC5 Switch Box

ITEM C40: 43260-30 – Cable UC5 Interface DTM 4 Pin 12in Stub

ITEM C41: 43220-03 - Cable UC5 Network 14 AWG - 3M

Technical Specifications

Module Installation

valve module

control module

Appendix A: Hydraulics for Older Sprayers

Connecting the Sensors to the CANbus

CABLE UC5 NETWORK HAGIE STS BOOM DISCONNECT TO 8-WAY

Pre-Install Checklist

Connecting the Sensors to the CAN-Bus

INTRODUCTION

John Deere 4630

Pull Type: Control Module on Tractor

Pull Type: Control Module on Sprayer

ITEM C26: 43240-26 – CABLE UC5 SWITCH BOX

ITEM C30: 43250-06 – CABLE UC5 BATTERY PIGTAIL

ITEM C40: 43260-02 – CABLE UC5 CAN BUS VT JD GS2

ITEM C40: 43260-08 – CABLE UC5 CAN BUS 4 PIN DT

APPENDIX A: ALTERNATE CONFIGURATION

technical specifications

UC5 Resource Upgrade Kit

UC5 Resource Kit

Calibration Stand Assembly and Alignment

Height Sensors

Roll Sensors

Linear Sensors

Frequently Asked Questions

Height Sensor Log Sheet

Roll Sensor Log Sheet

Linear Sensor Log Sheet

Appendix A – Adjusting 44730 Calibration Stand

TECHNICAL SPECIFICATIONS

ITEM C40: 43260-08 – Cable UC5 Interface CANbus 4-Pin Deutsch

SAFETY PRECAUTIONS

SYSTEM DESCRIPTION

ICON DESCRIPTIONS

OPERATION

Setting Control Options

Sprayer Manual Boom Height Switches

Setup

Retune

MAINTENANCE

UC5 MENU STRUCTURE

KEY FEATURES

SYSTEM OPERATION

UC5 KIT OPTIONS

UNDERSTANDING THE UC5 SYSTEM

Sensing Further Ahead of the Boom

Soil Mode and Crop Mode

SYSTEM SETUP

Automatic System Setup

Manual Setup

Position Sensor Installation

Roll Cylinder Installation

System Maintenance

Item C26: 43240-26 – Cable UC5 Switch Box

Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT

Item C41: 43210-01 - Cable UC5 Network 18 AWG - 1M

Settings

Sprayer Switches

Error Indicators

UNDERSTANDING THE UC5™ SYSTEM

Hydraulic Retune

Boom Geometry Test

OPTIONS MENU

Headland Assist

Oil Temp Alarm

Manual Valve Drive

DIAGNOSTICS MENU

DISPLAY SETTINGS

SOFTWARE UPDATE

Display Update

OPTIONAL KITS

Roll Bias (Active Roll Control™) Kit

TROUBLESHOOTING

Sensors

Modules

Boom Stability

Setup: Sensors

Setup: Valves

Setup: Switches

Diagnostics: Hydraulics

Diagnostics: Boom Movements

STATEMENT OF LIMITED WARRANTY

KIT PART

Appendix A: Fitting Specification

Control Module on Sprayer

Start Up and System Check

Quantity Picture

CABLE UC5 NETWORK HAGIE STS CAB TO BULKHEAD

Wing Roll Cylinder Air Bleed Procedure

Appendix A: Sensor Bracket Installation

Safety Precautions

Technical Specifications

UC5 Operation

NORAC Solutions

UC5 System Service and Diagnostics

UC5 System Maintenance

UC5 Menu Structure

Icon Descriptions

Contacting Support

Notes


Contents Table Of Contents Introduction Kit Part Hydraulic Installation Roll Sensor Installation Electrical Installation Software Setup Cable Drawings	Spray Height ControllerSummers(Main Lift & Enhanced Stability)Installation ManualSM03-4B Next / 17