Nordic Aluminium Global trac Htek Series Installation Instructions Manual
        |
seriesHtek2-circuit 277V Lighting Trackwith independent neutralsINSTALLATION INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSWhen installing or using this track system, basic safety precautions should always befollowed, including the following :1. Read all of these installation instructions before installing the GLOBAL Htek 277V lightingtrack system2. The GLOBAL Htek 277V track system is intended for use only with GLOBAL Htekcomponents and fixtures marked for use with GLOBAL Htek system. To reduce risk of fireand electric shock, do not use other components as part of this system.3. Track installation is to only be performed by a certified electrician in accordance with theNational Electrical Code and all local codes and ordinances.4. The GLOBAL Htek system is designed to be fed by two branch circuits rated 277VAC,20A, eg. the system is a two-circuit / two-neutral track and care must be taken to keepcircuits designated as circuit1 and circuit2 separate.5. Do not install the track in damp or wet locations.6. Do not install any parts of the track system less than 8 ft above the floor.7. Do not install any fixtures closer than six inches from combustible materials.8. Do not use this track with a power supply cord or convenience receptacle adapter.9. Do not install the track with electric power connected. Similarly, disconnect electricitywhen installing or removing fixtures or components or changing the configuration of thetrack.10. Do not attempt to energize anything other than Lighting Track Fixtures on the track. Toreduce the risk of fire and electrical shock, do not attempt to connect power tools,extension cords, appliances and the like to the track.SAVE THESE INSTRUCTIONSHTEK page 1(8)seriesInstallation instructions D2427eHtek2-circuit 277V Lighting Trackwith independent neutralsINSTALLATION INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSWhen installing or using this track system, basic safety precautions should always befollowed, including the following :1. Read all of these installation instructions before installing the GLOBAL Htek 277V lightingtrack system2. The GLOBAL Htek 277V track system is intended for use only with GLOBAL Htekcomponents and fixtures marked for use with GLOBAL Htek system. To reduce risk of fireand electric shock, do not use other components as part of this system.3. Track installation is to only be performed by a certified electrician in accordance with theNational Electrical Code and all local codes and ordinances.4. The GLOBAL Htek system is designed to be fed by two branch circuits rated 277VAC,20A, eg. the system is a two-circuit / two-neutral track and care must be taken to keepcircuits designated as circuit1 and circuit2 separate.5. Do not install the track in damp or wet locations.6. Do not install any parts of the track system less than 8 ft above the floor.7. Do not install any fixtures closer than six inches from combustible materials.8. Do not use this track with a power supply cord or convenience receptacle adapter.9. Do not install the track with electric power connected. Similarly, disconnect electricitywhen installing or removing fixtures or components or changing the configuration of thetrack.10. Do not attempt to energize anything other than Lighting Track Fixtures on the track. Toreduce the risk of fire and electrical shock, do not attempt to connect power tools,extension cords, appliances and the like to the track.SAVE THESE INSTRUCTIONSHTEK page 1(8)seriesHtek2-circuit 277V Lighting Trackwith independent neutralsINSTALLATION INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSWhen installing or using this track system, basic safety precautions should always befollowed, including the following :1. Read all of these installation instructions before installing the GLOBAL Htek 277V lightingtrack system2. The GLOBAL Htek 277V track system is intended for use only with GLOBAL Htekcomponents and fixtures marked for use with GLOBAL Htek system. To reduce risk of fireand electric shock, do not use other components as part of this system.3. Track installation is to only be performed by a certified electrician in accordance with theNational Electrical Code and all local codes and ordinances.4. The GLOBAL Htek system is designed to be fed by two branch circuits rated 277VAC,20A, eg. the system is a two-circuit / two-neutral track and care must be taken to keepcircuits designated as circuit1 and circuit2 separate.5. Do not install the track in damp or wet locations.6. Do not install any parts of the track system less than 8 ft above the floor.7. Do not install any fixtures closer than six inches from combustible materials.8. Do not use this track with a power supply cord or convenience receptacle adapter.9. Do not install the track with electric power connected. Similarly, disconnect electricitywhen installing or removing fixtures or components or changing the configuration of thetrack.10. Do not attempt to energize anything other than Lighting Track Fixtures on the track. Toreduce the risk of fire and electrical shock, do not attempt to connect power tools,extension cords, appliances and the like to the track.SAVE THESE INSTRUCTIONSHTEK page 1(8)GES 208 (8ft)GES 208 (8ft) oneone--circuit track, surfacecircuit track, surfacemountmountGES 212 (12ft)GES 212 (12ft)GET 304 (4ft)GET 304 (4ft)GET 308 (8ft) twotwo--circuit track, surfacecircuit track, surfacemountmountGET 312 (12ft)GET 312 (12ft)IMPORTANT SAFETY INSTRUCTIONSRead All Instructions Before InstallationRead All Instructions Before Installation The GLOBAL trac eco system is intended for use with GLOBAL trac ecocomponents and fixtures marked for use with the GLOBAL trac ecosystem. To reduce the risk of fire and electric shock, do not use othercomponents as part of this system. Track installation is only to be performed by a certified electrician inaccordance with the National Electrical Code and all local codes andordinances. Single-circuit system: The eco GES track system is designed to besupplied by a single 120 volt branch circuit with a maximum capacity of20 amps.Two-circuit system: The eco GET track system is designed to besupplied by a balanced 120/240 volt, three-wire branch circuit with amaximum capacity of 40 amps. Do not use this track system with a power supply cord or conveniencereceptacle adapter. Do not install any fixtures closer than six inches from combustiblematerials. Do not install the track in damp or wet locations. Do not install the track with electric power connected. Similarly,disconnect electricity when installing or removing fixtures or componentsor changing the configuration of the track. Do not attach anything other than UL listed lighting fixtures markedforforforforuse with Nordic Aluminium GLOBAL trach Nordic Aluminium GLOBAL trach Nordic Aluminium GLOBAL tracuse w h Nordic Aluminium GLOBAL trac ecosystem onlysystem onlysystem onlysystem only to the track.IMPORTANTSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENADDING FIXTURES OR CHANGING THE TRACKADDING FIXTURES OR CHANGING THE TRACKADDING FIXTURES OR CHANGING THE TRACKADDING FIXTURES OR CHANGING THE TRACKCONFIGURATIONCONFIGURATIONCONFIGURATIONCONFIGURATIONGES 204 (4ftGES 204 (4ftGES 208 (8ft)GES 208 (8ft) oneone--circuit track, surfacecircuit track, surfacemountmountGES 212 (12ft)GES 212 (12ft)GET 304 (4ft)GET 304 (4ft)GET 308 (8ft) twotwo--circuit track, surfacecircuit track, surfacemountmountGET 312 (12ft)GET 312 (12ft)IMPORTANT SAFETY INSTRUCTIONSRead All Instructions Before InstallationRead All Instructions Before Installation The GLOBAL trac eco system is intended for use with GLOBAL trac ecocomponents and fixtures marked for use with the GLOBAL trac ecosystem. To reduce the risk of fire and electric shock, do not use othercomponents as part of this system. Track installation is only to be performed by a certified electrician inaccordance with the National Electrical Code and all local codes andordinances. Single-circuit system: The eco GES track system is designed to besupplied by a single 120 volt branch circuit with a maximum capacity of20 amps.Two-circuit system: The eco GET track system is designed to besupplied by a balanced 120/240 volt, three-wire branch circuit with amaximum capacity of 40 amps. Do not use this track system with a power supply cord or conveniencereceptacle adapter. Do not install any fixtures closer than six inches from combustiblematerials. Do not install the track in damp or wet locations. Do not install the track with electric power connected. Similarly,disconnect electricity when installing or removing fixtures or componentsor changing the configuration of the track. Do not attach anything other than UL listed lighting fixtures markedforforforforuse with Nordic Aluminium GLOBAL trach Nordic Aluminium GLOBAL trach Nordic Aluminium GLOBAL tracuse w h Nordic Aluminium GLOBAL trac ecosystem onlysystem onlysystem onlysystem only to the track.IMPORTANTSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHENADDING FIXTURES OR CHANGING THE TRACKADDING FIXTURES OR CHANGING THE TRACKADDING FIXTURES OR CHANGING THE TRACKADDING FIXTURES OR CHANGING THE TRACKCONFIGURATIONCONFIGURATIONCONFIGURATIONCONFIGURATIONINSTRUCTIONS) |
Related manuals for Nordic Aluminium Global trac Htek Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine