Nortek 904176 Installation Instructions Manual

Nortek 904176 Installation Instructions Manual Manual pdf 1 page image

Concentric Vent Termination Kit for Condensing FurnacesSpeCial VenTing requiremenTS ForinSTallaTionS in CanadaInstallation in Canada must conform to the requirements ofCSA B149 code. Vent systems must be composed of pipe,fittings, cements, and primers listed to ULC S636. Thisconcentric vent termination kit has been certified to ULCS636 for use with piping and vent components which havebeen certified to this standard. Follow the manufacturer’sinstructions in the use of primer and cement and neveruse primer or cement beyond its expiration date.The safe operation, as defined by ULC S636, of the ventsystem and this termination kit is based on following theseinstallation instructions, the vent system manufacturer’sinstallation instructions, and proper use of primer andcement. Acceptability under Canadian standard CSAB149 is dependent upon full compliance with all installationinstructions. Under this standard, it is recommended thatthe vent system be checked once a year by qualifiedservice personnel. The authority having jurisdiction (gasinspection authority, municipal building department, firedepartment, etc) should be consulted before installationto determine the need to obtain a permit.ConSigneS SpÉCialeS pourl’inSTallaTion de VenTillaTion auCanadaL’installation faite au Canada doit se conformer aux exigencesdu code CSA B149. Ce systême de ventillation doit secomposer de tuyaux, raccords, ciments et apprêts conformesau ULC S636. Ce systême de ventillation concentrique a étécertifié ULC S636 pour être utilisé avec les composantes quisont certifiés. Bien suivre les indications du manufacturierlors de l’utilisation de l’apprêt et du ciment et ne pas utiliserceux--ci si la date d’expiration est atteinte.Le bon fonctionnement de ce systême de ventillation estconditionnel à l’installation tel que défini par le ULC S636c’est à dire: bien suivre les consignes ci--haut mentionnéesainsi que les instructions du manufacturier et aussi une bonneutilisation de l’apprêt et du ciment. L’acceptation du standardCanadien CSA B419 est directement relié à l’installationconforme aux instructions ci--haut mentionnées. Le standardCanadien recommande l’ inspection par un personelqualifié et ce, une fois par année. Les autoritées ayantjuridiction (inspecteurs de gas, inspecteurs en bâtiments,département des incendies, etc) devraient être consultéesavant l’installation afin de déterminer si un permis est requis.imporTanT SaFeTY inFormaTionPlease read all instructions before installing this kit. Payattention to all safety warnings and any other specialnotes highlighted in the manual. Safety markings areused frequently throughout this manual to designate adegree or level of seriousness and should not be ignored.Warning indicates a potentially hazardous situation thatif not avoided, could result in personal injury or death.CauTion indicates a potentially hazardous situation thatif not avoided, may result in minor or moderate injury orproperty damage.Warning:riSK oF eleCTriCal SHoCKShut off all electrical power to the unit beforeperforming any maintenance or service onthe system. Failure to follow this warning cancause serious injury, fire, electrical shock, ordeath.• The installer performing this work assumes allresponsibility when installing this kit. These instructionsare primarily intended to assist qualified individualsexperienced in the proper installation of this kit. Somelocal codes may require licensed installation/servicepersonnel for this type of equipment. Safety shouldalways be the deciding factor when installing this productand using common sense plays an important role aswell. Improper installation of the components or failureto follow safety warnings could result in serious injury,death, or property damage.• Unless noted otherwise in these instructions, only factoryauthorized parts or accessory kits may be used with thisproduct. Improper installation, service, adjustment, ormaintenance may cause fire, electrical shock or otherhazardous conditions which may result in personal injuryor property damage.• Please read all instructions carefully before starting theinstallation. If a problem occurs, check the instructionsand follow recommendations given.• The information shown in these instructions must befollowed during the installation of this kit. Unqualifiedindividuals should not attempt to interpret theseinstructions or install this equipment. If you do notpossess mechanical skills or tools, call your local dealerfor assistance.• Use caution when handling the appliance or removingcomponents. Personal injury can occur from sharp metaledges present in all sheet metal constructed equipment.inSTallaTion inSTruCTionS

/ 4

Related manuals for Nortek 904176