Nortek Security & Control Mighty Mule MMT103 Instructions Manual
RED LEDLEARN BUTTONLights FlashRED LEDFlashDESCRIPTION:The MMT103 Code Safe entry remote is a wireless radio control designed for use with Mighty Mulegarage door openers and can also be programmed to your Mighty Mule gate openers. One remote fortwo or three devices.Each of the remote’s three buttons will send a unique code when pressed. All buttons can be used toactivate an individual Mighty Mule garage door opener, multiple Mighty Mule garage door openers orMighty Mule garage door opener(s) and gate opener(s).MMT1033-BUTTON ENTRY REMOTEInstructionsPROGRAMMING:Press the operator’s LEARN button (S3) untilthe operator’s red LED flashes once and thelight turns on. A remote must be added whilethe light is still on (15 seconds).Send a signal from the desired button on theremote. The operator’s light and the red LEDwill flash once if the remote was added.Repeat to program additional buttons for othergarage door openers.After programming, test the remote from variouslocations. Be sure the door or gate areas are clear.Activate the remote and verify that the receivertriggers the opener(s).®PRINTER’S INSTRUCTIONS:INSTR, INSTL, MMT103 - P/N: 10015841 C - INK: BLACK - MATERIAL: 20# MEAD BOND - SIZE: 8.500” x 11.00” - SCALE: 1-1PROGRAMMING THE REMOTE TO THE GARAGE DOOR OPENERDELETING A REMOTE FROM THE GARAGE DOOR OPENER OR GATE OPENERPROGRAMMING THE REMOTE TO MIGHTY MULE 7TH GENERATION AUTOMATIC GATE OPENER1122212If you have a Mighty Mule gate opener, you can program one of thebuttons to open the gate also.Press and hold button 1 and button 3 at the same time for 5seconds. The LED will turn on, then release the buttons.Press and release the button that you want to learn the gateopener code to.Hold the gate opener remote with the front/top facing the side ofthe MMT103. Press the button on the gate opener remote andthe LED on the MMT103 will blink twice when it has successfullylearned the code.The button you programmed will now transmit the gate opener code asindicated by the LED being solid on when the button is pressed.PROGRAMMING/LEARNING A GATE OPENER REMOTE®Button #1LEDButton #31®Press and release the button youwant to learn the gate operator code2®Press and hold the gate operator remote buttonuntil the LED on the MMT103 blinks twice®LED3123DELETING A DIP SWITCH CODEPress and hold button 1 and button 3 at the same time forabout 5 seconds. The LED will turn on, then release thebuttons.Press and hold the button you want to delete a code from for5 seconds, then the LED will blink twice indicating the DIPswitch code was successfully removed.122®Press and hold the button you wantto delete a code from for five seconds.®Button #1LEDButton #31Copyright© 2019 Nortek Security and Control, LLC 10015841 CWhen the red light on the remote glows dimly, or fails to light at allwhen the remote is activated, the batteries need replacing.Twist a coin, visor clip or screw drive in slot to open case.Lift off top of case.Carefully remove the circuit board.Remove old battery and properly dispose them.Replace battery with new Type 2032 battery – PLUS SIDE UP.Re-assemble the remote.234561Mighty Mule® is the retail brand of Nortek Security and Control, LLC5919 Sea Otter Pl • Carlsbad, CA 92010Mighty Mule Sales: 800-543-4283 • Fax 850-575-8912Mighty Mule Technical Service: 800-543-1236For more information on Mighty Mule’s full line of Automatic Gate Openers and Access Controls visit www.mightymule.comREPLACING REMOTE’S BATTERYIf a remote is already programmed to the opener and you want to delete it, follow the same procedure as PROGRAMMING THE REMOTEabove. The opener will recognize the remote and delete it from memory.4 5 61 2 3WARNINGKEEP BATTERIES OUT REACH OF CHILDREN. Swallowing batteries can lead to serious injury or death. If you suspectsomeone has swallowed a battery, go to the hospital immediately. Do not induce vomiting or eat or drink anything.For more information, call the National Battery Ingestion Hotline: 202-625-3333.The battery identification number for this product is CR2032.WARNING: Changes, modifications or adjustments not expressly approved by Nortek Security and Control, LLC could void the user’s authority tooperate this equipment. There Are No User Serviceable Parts.NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not causeharmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device complies with Industry Canada License-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may notcause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.MIGHTY MULE LIMITED WARRANTYThis product is warranted to the consumer against defects in material and workmanship for one year from the date of purchase. This warranty appliesto first retail buyers of new devices. Mighty Mule will repair, or at its option, replace, any device it finds that requires service under this warranty, and willreturn the repaired or replaced device to the consumer at the Might Mule’s cost. For warranty service and shipping instructions contact Mighty Mule TechService. Devices must be sent to Mighty Mule for service at owner’s expense. The remedies provided by this warranty are exclusive. Implied warrantiesunder state law are to the one year period of this written warranty. Some states do not allow limitations on how long an implied warranty lasts, so theabove limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send copy with equipment should repairbe required. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Mighty Mule Technical Services at 1-800-543-1236 for an RPA# and other important details.S4S3S2LED1LED2LED3Press the gate opener’s LEARN button (S3) locatedon the control board.Press the desired button on the remote tocomplete programming process. The remote is nowprogrammed to the gate opener.1 |
Related manuals for Nortek Security & Control 142980399
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine