Nortel Communication Server 1000DASS2 FundamentalsNN43001-571.

Nortel Communication Server 1000 Manual

revision history

About this document

Applicable systems

Intended audience

Preparing for installation

Unpacking and inspecting

Installing ISDN BRI hardware

Procedure 1 Selecting the card slots

Procedure 2 Remove the module cover for card installation

Procedure 3 Installing the MISP

Procedure 5 Installing the BRSC, SILC, and UILC

Procedure 6 Remove the BRSC, SILC, and UILC

Procedure 8 Connect the modules to the MDF

Procedure 9 Cross-connecting SILC and/or UILC ports to the building wiring

Procedure 10 Connecting the ISDN BRI terminals to the DSL

Installing ISDN BRI hardware for trunk applications

Procedure 11 Providing clock referencing on the SILC

Procedure 12 Connecting clock reference cables

Preparing the system

Setting up ISDN BRI test terminals and trunks

Conﬁguring ISDN BRI hardware

Conﬁguring ISDN BRI trunking with IP expansion cabinets or MG 1000S systems

Installation procedures

Procedure 14 Selecting the card slots

Procedure 15 Installing the MISP

Procedure 16 Removing the MISP

Procedure 17 Installing the SILCs and UILCs

Procedure 18 Removing the SILC and UILC

Procedure 20 Connecting system cables to the cross-connect terminal

Procedure 21 Cross-connecting the DSLs at the cross-connect terminal

Procedure 22 Connecting the terminating resistor to the SILC DSL

Procedure 23 Connecting the ISDN BRI terminals to the DSL

Procedure 24 Initializing a Nortel Networks M5317TDX terminal

Procedure 25 Connecting the system cables to the cross-connect terminal

Procedure 26 Cross-connecting DSLs at the cross-connect terminal

Testing ISDN BRI functions

Voice calls

Procedure 28 Perform a Call Waiting test

Procedure 29 Performing a Call Forward No Answer test

Procedure 30 Perform a Calling Line Identiﬁcation Presentation test

Procedure 31 Perform an ISDN BRI Conference test

Procedure 32 Perform a Call Join test on Conference

Procedure 33 Perform a hunting test

Procedure 34 Perform an ISDN BRI NI-1 Call Forward All Calls test

Procedure 35 Perform an ISDN BRI ETSI Call Forwarding Unconditional test

Circuit-switched data calls

Packet data transmission

Procedure 38 Perform a D-channel packet data transmission test using an external packet handler

Procedure 40 Perform a B-channel Switched Virtual Circuit packet data transmission test using an MPH

Testing an ISDN BRI trunk

Generating trafﬁc reports

Communication Server 1000

Procedure

Revision history

Getting help from the Nortel Web site

Getting help from a specialist by using an Express Routing Code

on the Nortel web site

System information

Safety instructions

Lifting system equipment

Installing telephones

Installation summary

Installation tasks

System components

Introduction

CS 1000E Common Processor Pentium Mobile Call Server

Signaling Server

Media Gateway Controller

MC32S Media Card

Media Gateway

Media Gateway Expander

inch Rack Mount Kit

BayStack 470 Switch

BayStack 460 Layer 2 switch

inch rack

Miscellaneous system components

Rack-mounting the components

Lifting system components

Guidelines for component placement in a rack

Rack-mounting a Media Gateway or Media Gateway Expander

Rack-mounting a Terminal Server

Installing system grounds

Installing a ground bar

Installing an NTBK80 Ground Bar

Installing an NTDU6201 Ground Bar

Grounding an ISP1100 Signaling Server

Grounding Media Gateways powered by the same electrical panel

Grounding a Media Gateway powered by multiple electrical panels

Grounding other rack-mounted components

Grounding equipment in the UK

Installing and connecting CS 1000E hardware

Connecting CP PM Call Server 0 to CP PM Call Server 1

Connecting co-located CP PM Call Servers

Installing the cards

Installing a DSP Daughterboard

Installing the CP PM card

Cabling the cards

adapter onto a Media Card

Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter

Connecting a Media Card to the ELAN subnet

Connecting a Media Card to the TLAN subnet

Installing software on the CS 1000E

Installing the software

Reconfiguring I/O ports and call registers

Testing the CP PM Call Server

Making the system redundant

Testing CP PM Call Server 0

Switching call processing

Testing CP PM Call Server 1

Configuring initial IP configuration data on MGC

Configuring the MGC on the Call Server

Call Server

Configuring login IDs and passwords

Enabling the multi-user option

Configuring pseudo-terminals (PTYs)

Checking PTY status

Configuring Virtual Tone and Conference Circuits

Configuring the MG 1000E Bandwidth Management Zones

Configuring the MG 1000E ports

Configuring Digitone Receivers

Configuring Tone Detectors

Launching Element Manager

Importing preconfigured IP telephony files

Reviewing and submitting IP telephony node configuration files

Installing a Signaling Server

Readiness checklist

Installing the CP PM Signaling Server hardware

Connections

Connecting a Nortel CP PM Signaling Server

E system