NuTone ChromaComfort Installation Manual

Contents

retrofit installation

NuTone ChromaComfort Installation Manual Manual pdf 1 page image

1OPTION - To mount housing anywhere between ceiling framing:Use optional Hanger Bar Kit (sold separately from local distributorsor website). Follow mounting instructions included with kit.ROOF CAP* (with built-in damper)WALL CAP*(with built-indamper)4-IN. ROUNDELBOWS*FANHOUSINGSeal gapsaroundhousing.Seal duct jointswith tape.INSULATION(Place around andover fan housing.)POWERCABLE ** Purchase separately.ORKeep ductruns short.4-IN. ROUNDDUCT*IMPORTANT - The ducting from this fan to the outside of the buildinghas a strong effect on the air flow, noise and energy use of the fan. Usethe shortest, straightest duct routing possible for best performance, andavoid installing the fan with smaller ducts than recommended. Insulationaround the ducts can reduce energy loss and inhibit mold growth. Fansinstalled with existing ducts may not achieve their rated airflow.WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,OBSERVE THE FOLLOWING:1. Use this unit only in the manner intended by the manufacturer. If you havequestions, contact the manufacturer at the address or telephone number listedin the warranty.2. Before servicing or cleaning unit, switch power off at service panel and lockthe service disconnecting means to prevent power from being switched onaccidentally. When the service disconnecting means cannot be locked, securelyfasten a prominent warning device, such as a tag, to the service panel.3. Installation work and electrical wiring must be done by a qualified person(s)in accordance with all applicable codes and standards, including fire-ratedconstruction codes and standards.4. Sufficient air is needed for proper combustion and exhausting of gases throughthe flue (chimney) of fuel burning equipment to prevent backdrafting. Followthe heating equipment manufacturer’s guideline and safety standards such asthose published by the National Fire Protection Association (NFPA), and theAmerican Society for Heating, Refrigeration and Air Conditioning Engineers(ASHRAE), and the local code authorities.5. When cutting or drilling into wall or ceiling, do not damage electrical wiringand other hidden utilities.6. Ducted fans must always be vented to the outdoors.7. Acceptable for use over a tub or shower when connected to a GFCI (GroundFault Circuit Interrupter) - protected branch circuit (ceiling installation only).8. This unit must be grounded.CAUTION1. For general ventilating use only. Do not use to exhaust hazardous or explosivematerials and vapors.2. This product can be installed in a wall if mounted 8-ft. or more above the floor.3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keepdrywall spray, construction dust, etc. off power unit.4. Please read specification label on product for further information andrequirements.READ AND SAVE THESE INSTRUCTIONSCookingEquipmentFloorCOOKING AREADo not install above orinside this area.45 o 45 oNOT FOR USE INA COOKING AREA.CLEANING & MAINTENANCEFor quiet and efficient operation, long life, and attractive appearance- lower or remove grille and vacuum interior of unit with the dustingbrush attachment.The motor is permanently lubricated and never needs oiling. If themotor bearings are making excessive or unusual noises, replace theblower assembly (includes motor and impeller).OPERATIONThe Chroma Fan/Light must be operated using only the wall controlincluded. See separate operating instructions. DO NOT operate theChroma Fan/Light with any other switches or controls.For Warranty Statement, Service Parts, Technical Support, or toRegister your product, please visit our website or call:In the United States - Broan.com 800-637-1453 or NuTone.com888-336-6151. In Canada - Broan.ca or NuTone.ca 877-896-1119ChromaComfortTMFan/Light InstallationThe Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG,Inc. and any use of such marks by Broan-NuTone LLC is under license. Other trademark andtrade names are those of their respective owners.NOTE: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occurin a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules and RSS-210 of Canada. Operation issubject to the following two conditions:(1) This device may not cause interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. FCC IDs: 2ADLL-RGB001 & 2ADLL-RGB002 IC IDs: 2143B-RGB001 & 2143B-RGB002This Bluetooth® wireless technology enabled luminaire complies with FCC radiationexposure limits set forth for an uncontrolled environment. End users must follow thespecific operating instructions for satisfying exposure compliance. This luminaire must notbe co-located or operate in conjunction with any other antenna or transmitter.Changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.