PAC C2R-CHY4 User Manual

Also see for C2R-CHY4: Installation guide Installation instructions

PAC C2R-CHY4 User Manual Manual pdf 1 page image

Pacific Accessory Corporation - Santa Ana, CA 92705techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.comDISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-CHY4 be held liable for consequential damages sustained inconnection with the C2R-CHY4. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assumeobligation or liability in relation to the C2R-CHY4 other than its replacement.10-13-08J1850Class 2VPWClass 2J18501 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 01 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0ArbitrationEODCRC1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 01 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0Class 2Class 2J1850Radio Replacement Interfacewith Nav Outputs for all ChryslerDodge / Jeep CANbus Vehicles Withor Without Premium Audio SystemsC2R-CHY4Installation Notes:1. Only one of the two provided radio harnesses will be used. Remove the factory installed radioto determine the correct harness for your particular vehicle.2. Vehicles without a factory amplifier: Connect the aftermarket radio’s front and rear speakerwires to the 22 pin plug.3. Vehicles with a factory amplifier: The factory amplifier only accepts two audio channels(left and right). The amplifier’s fading is controlled by data communication from the factory radio.The aftermarket radio does not have the ability to control the amplifier’s fader. Connect the frontoutputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This willallow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used.4. Vehicles with a manual transmission will not support a reverse trigger output.5.The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory wire. The accessorywire supplies +12v, 1 amp max when key is in the accessory or ignition position (fig. 1: If more current is needed).6. 11 pin plug (to CAN INTERFACE):Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp present!White/Green - SWC output.Green - Connect this wire to the radio’s reverse input wire only.Orange/White - Connect this wire to the radio’s Illumination input wire only.Violet/White - Connect this wire to the radio’s VSS input wire only.Red/White - Connect this wire to the radio’s parking brake input wire only.Note: Do not connect these wires to any circuit other than the radio’s wire harness.7. 11 pin plug (to SWC INTERFACE):This is a quick connection to a radio specific SWC interface. No additional connections arenecessary other than radio control connections. Plug the radio specific SWC interface in tothis connector and program the radio specific SWC interface for version 2. Do not cut theloops. Refer to the SWC interface instruction manual for the radio specific control functionprogramming order.8. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brakeand Illumination outputs. For the most current and Up-to-Date application guide pleasevisit www.pac-audio.com1.2.3.4.5.6.Fig. 1(using a SPDT relay)85 86308787aGroundHigh Current 12v(Fused)12v Acc.FromInterfaceNew HighCurrent OutputDiode 1N4005or equivelant9 123456781011Accessory Output+12volts 1amp max.Chrysler9 19 123456781011 9 1SWC Interface.Program for Version 2Radio Specific SteeringWheel Control Interface(Sold Separately)Program SWCInterface for Version 2.CAN INTERFACENavigation outputs andAmplifier Remote InputSee Chart for wire colordescriptions.Radio Connections. See asideChart for color description.Yellow Battery +12vBlack GroundBlue Antenna On InputWhite Front L + inputWhite / Black Front L - inputGrey Front R + inputGrey / Black Front R - inputGreen Rear L + inputGreen / Black Rear L - inputPurple Rear R + inputPurple / Black Rear R - inputRadio Connection Chart:(Read the Installation Notes before makingconnections to the provided radio harness)CAN Interface Connection Chart:Red Acc. Output (1 amp)Red / White P.B. Output (-)Purple / White VSS Output (Pulse)Orange / White Illum. Output (+)Green Reverse Output (+)White / Green SWC OutputBlue / White Amp Turn On Input

/ 1

Related manuals for PAC C2R-CHY4