PASCO PS-3214 Operation Manual
Also see for PS-3214: Reference guideProduct guideReplacement instructions
012-16026A support@pasco.com | 1 |PASCO Wireless Drop Counter PS-3214 www.pasco.com - (800) 772-8700Software: SPARKvue or PASCO CapstonePower: Rechargeable BatteryConnection: or USBConnection: or USB012-16026A support@pasco.com | 1 |Software: SPARKvue or PASCO CapstonePower: Rechargeable BatteryPASCO Wireless Drop Counter PS-3214 www.pasco.com - (800) 772-8700INITIAL STEP - Charge it: On the bottom of the sensor, pry open therubber cover to reveal the Micro USB Port. Use the included microUSB cable to connect the sensor to a USB port or a USB charger (suchas PS-2575). If the cable is connected to a USB port, the Battery LEDshines yellow to show that the battery is charging. When the batteryis charged, the Battery LED shines green. If the cable is connected toa USB charger, the Battery LED shines yellow and the Bluetooth sta-tus LED blinks red to indicate that the sensor is ready to connect to adevice (such as a computer or tablet).1. Make the Connection: Start the PASCO data collection software.• For USB connection to a USB port: Make sure the USB cable isconnected. In SPARKvue: Click or Touch the “Sensor Data” icon inthe Welcome Screen. In PASCO Capstone, select ‘Hardware Setup”and check that the sensor appears in the “Hardware Setup” window.• For Bluetooth connection: If the sensor is not already on, pressthe ON button at the top of the sensor to turn it on. (NOTE: The following procedure also works if the sensor is connected to a USB charger.) InSPARKvue: Touch or Click the Sensor Data icon in the Welcome Screen. In the “Connected Devices” list, select the correct address that matchesthe XXX-XXX Device ID number found on the sensor. Select a measurement, and then select a “Template” to open a data display. In PASCOCapstone, select “Hardware Setup” in the “Tools” palette. Select the desired sensor type that matches the Device ID XXX-XXX number on thesensor. Close the “Hardware Setup” window.2. Set Up the Sensor: Arrange the sensor with the included syringe holder, syringe, and drop dispenser so that drops will pass through the DropWindow into a receptacle below.3. Collect Data: In SPARKvue, Select the “Start” button. In PASCO Capstone: Select a display, set up the measurement in the display, and select“Record”. 4. Analyze the Data: Use the PASCO Data Collection software (SPARKvue or Capstone) to interpret the data.Battery LEDMicroUSBCableCharging Time:About 3 hoursTop viewFor Temperature SensorFor pH SensorBluetooth LEDDrop Indicator LEDDrop WindowDevice IDFor SupportRodON/OFFUSB Port Cover onthe Bottom of theSensorINITIAL STEP - Charge it: On the bottom of the sensor, pry open therubber cover to reveal the Micro USB Port. Use the included microUSB cable to connect the sensor to a USB port or a USB charger (suchas PS-2575). If the cable is connected to a USB port, the Battery LEDshines yellow to show that the battery is charging. When the batteryis charged, the Battery LED shines green. If the cable is connected toa USB charger, the Battery LED shines yellow and the Bluetooth sta-tus LED blinks red to indicate that the sensor is ready to connect to adevice (such as a computer or tablet).1. Make the Connection: Start the PASCO data collection software.• For USB connection to a USB port: Make sure the USB cable isconnected. In SPARKvue: Click or Touch the “Sensor Data” icon inthe Welcome Screen. In PASCO Capstone, select ‘Hardware Setup”and check that the sensor appears in the “Hardware Setup” window.• For Bluetooth connection: If the sensor is not already on, pressthe ON button at the top of the sensor to turn it on. (NOTE: The following procedure also works if the sensor is connected to a USB charger.) InSPARKvue: Touch or Click the Sensor Data icon in the Welcome Screen. In the “Connected Devices” list, select the correct address that matchesthe XXX-XXX Device ID number found on the sensor. Select a measurement, and then select a “Template” to open a data display. In PASCOCapstone, select “Hardware Setup” in the “Tools” palette. Select the desired sensor type that matches the Device ID XXX-XXX number on thesensor. Close the “Hardware Setup” window.2. Set Up the Sensor: Arrange the sensor with the included syringe holder, syringe, and drop dispenser so that drops will pass through the DropWindow into a receptacle below.3. Collect Data: In SPARKvue, Select the “Start” button. In PASCO Capstone: Select a display, set up the measurement in the display, and select“Record”. 4. Analyze the Data: Use the PASCO Data Collection software (SPARKvue or Capstone) to interpret the data.Battery LEDMicroUSBCableCharging Time:About 3 hoursTop viewFor Temperature SensorFor pH SensorBluetooth LEDDrop Indicator LEDDrop WindowDevice IDFor SupportRodON/OFFUSB Port Cover onthe Bottom of theSensor |
Related manuals for PASCO PS-3214
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine