Panasonic VL-MV26 Installation Manual

Also see for VL-MV26: Installation guide Manual Operating instructions

Panasonic VL-MV26 Installation Manual Manual pdf 1 page image

Installation GuideNote to the installerLBefore attempting to connect or operate this product, please read the label on the rear ofthe main monitor.LPlease read this guide carefully, and install the product safely and correctly by following theinstructions. Carefully read the information found in the section titled "For your safety" in particular.LOnly use attachments/accessories specified by the manufacturer.LThe installation shall be carried out in accordance with all applicable installation rules.LPanasonic assumes no responsibility for injuries or property damage resulting fromfailures arising out of improper installation or operation inconsistent with this guide.Additionally, any resulting malfunction will not be covered under the warranty.LPlease confirm the wiring schematic diagram in this Installation Guide when you increasean optional equipment.LAfter installation, make sure to leave this guide with the customer.Model Name Main Monitor StationModel No. VL-MV26Included accessories for installationN For the main monitor N Power supply unit and related itemsMountingbracket × 1Power supply unit× 1(Part No. VL-PS240)Screw × 2(4 mm × 16 mm) Cable binder × 2 Screw × 2(4 mm × 40 mm)1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japanhttp://www.panasonic.com© Panasonic Corporation 2016PNQW5093WA C0416HH2037Main monitor station is described as"main monitor" in this guide.Main Monitor StationVL-MV26CAUTION● If the wiring is underground, do not make any connections underground.● If the wiring is underground, use a protection tube.● If the wiring is outdoors, use a protection tube or a surge protector.● Install the product securely adhering to the instructions in this guide to prevent it fromfalling off the wall. Avoid installing onto low-strength walls, such as gypsum board, ALC(autoclaved lightweight concrete), concrete block, or veneer (less than 18 mm thick) walls.Preventing electric shockPreventing injuryFor your safetyTo prevent severe injury and loss of life/property, read this section carefully before using theproduct to ensure proper and safe operation of your product.WARNINGPreventing fire, electric shock and short circuits● Leave installation work to the dealer.Installation work requires technique and experiences. Failure to observe this maycause fire, electric shock, injury, or damage to the product. Consult the dealer.● Electrical connection work should be performed by certified personnel only. Certificationis required for performing electrical connection work. Consult your dealer.● Use only the specified power supply unit.● Do not attempt to disassemble or modify this product. Contact an authorised service centre for repairs.● Never install wiring during a lightning storm.● Do not connect non-specified devices.● Do not connect a power cable to a terminal that is not specified in this guide.● When opening holes in walls for installation or wiring, or when securing the power cable,make sure you do not damage existing wiring and ductwork.● Do not make any wiring connections when the power supply is turned on.● Do not use the supplied power supply unit for outdoor installations (it is for indoor use only).● Do not install the main monitor and power supply unit in the following places:- Places where the main monitor and power supply unit may be splashed with water or chemicals.- Places where there is a high concentration of dust, or high humidity.● Do not perform any actions (such as fabricating, twisting, stretching, bundling, forcibly bending,damaging, altering, exposing to heat sources, or placing heavy objects on the power cable)that may damage the power cable. Using the product with a damaged power cable may causeelectric shock, short circuits, or fire. Contact an authorised service centre for repairs.● When existing chime wires are used, it is possible that they contain AC voltage. Contactan authorised service centre.Attach directly to a wallAttach the power supply unit to the wall securely.A Screws (accessory) × 2AInstalling the main monitor1 Attach the mounting bracket to the wall securely using the screws (4 mm × 16 mm).● Install the mounting bracket on a vertical flat wall.● Before drilling, refer to "Before installation" for installation location.83.5 mmScrewsWallWire (Not included)Mounting bracket2 Connect the DC cable and wires.● Connect the wires correctly according to "Wiring schematic diagram".A Remove screw A and then remove theterminal cover.B Press the cable release button whileinserting the wires of the DC cable to theterminal connectors (non-polar).C Use the cable binder (accessory) tosecure the DC cable (double-coatedarea) to the main monitor.D Make sure to replace the terminal cover.How to connect the DC cable:While pressing on the button with a point-ed object such as a screwdriver, insertthe wire into the terminal connector. (Todisconnect a wire, while pressing on thebutton, pull out the wire.)Important:Do not connect the power cable.(Damage may occur.)How to make wiring connections:Terminal coverScrew ACable release button50 mm or more12 mm9 mmButton TerminalAttach to the DIN railAttach in the order described below so that hook (b) is positioned at the bottom.1 Hang hook (a) on the DIN rail (A), and then pull and hold the lever down (B).2 Secure hook (b) to the DIN rail (C).Hook (a)ABCHook (b)Before installationTo avoid malfunction or communication disturbances, do not install the main monitor in thefollowing locations:− Places where vibration or any other kind of impact occurs.− Places where echoing is frequent.− Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.− Within 2 m of a TV, microwave, personal computer, air conditioner or any other electrical device.Standard installation position of the main monitorPlace the main monitor in a location that your eyes are the same height as the centre of the display.If a position of installation for the main monitor is specifiedInstall the mounting bracket to one of the following positions.Position of installation for the main monitor70 mm64.5 mmNote:LIn areas surrounded by a high electrical field, disturbances may occur in the main monitor’s image or sound.LDo not place any objects within 20 cm of the main monitor. This may cause communication errors or malfunction.LDo not install the main monitor inside a wall.LDo not install the main monitor in places where it will be affected by extremely high-frequency radio waves(near broadcasting antennas etc.). This may cause the display to flicker or an interrupting noise to occur.Installing the power supply unitN About the installation location● The device must be installed inside an electrical panel or cabinet.● A readily accessible disconnect device shall be incorporated external to the equipment.− External disconnect device must be certified and have a creepage and clearance distance of 3 mm or more.N Precautions for wiring● Make sure you turn off the power at the breaker before performing any wiring work.● Always connect AC or DC cables to the appropriate connection terminals. Incorrectlyconnecting the AC or DC cables may damage the power supply unit.● To prevent the power cables from disconnecting and to prevent electric shock, secure thepower cables using the cable binders (accessory) and attach the cable covers.How to connect the power cable (AC/DC)1 Strip the AC/DC cables as follows:7 mm45 mm25 mm7 mm2 Remove the screws (B) and then removethe cable covers (A).3 Connect the AC/DC cable to the AC INterminal/DC OUT terminal on the top andbottom of the power supply unit, and thensecure the wires by tightening the screws.● Recommended torque:− AC terminal: 0.5 N·m {5.1 kgf·cm}− DC terminal: 0.45 N·m {4.6 kgf·cm}AC cable*1DC cableScrews*1Cable binders (accessory)4 Use the cable binders (accessory) tosecure the AC/DC cables (double-coatedarea) to the power supply unit.5 Make sure to replace the cable covers (A).Connect the power supply unit (accessory) and AC/DC cables (locally procured).CAUTIONInsert the cables firmly all the wayinto the terminals.If the cables are not inserted allthe way, heat may be generated.*1 Do not connect the AC cable and DCcable inversely. That would be a causeof malfunctions.Make sure that there are no bare wiresexposed outside the product.Screws (B)Cable covers (A)DC OUT terminalAC cablebinder holeAC IN terminalDC cablebinder holePower supply unit (with cable coversremoved)3 Mount the main monitor to the mounting bracket.3-1 Line up the tab on the bottom of the bracket with the groove on the main monitor (A).3-2 Line up the tab on the top of the bracket with the groove on the main monitor, andpush the main monitor down until it is secure (B).WallWiring schematic diagramSet up correctly according to the following wiring schematic diagram and "Wire type andlength".NPNPNPNPDC INLobbyStationControlBoxDistribution BoxMain Monitor(up to 20 per Distribution box)Door BellorEmergencyCall ButtonPOWER SUPPLY UNITNP: Non-polarisedConnecting an optional lobby station for apartment complexesBe sure to perform the following to ensure proper operation:● Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the distribution box.Connecting a door bell● Connect terminal IN1/IN2 on the main monitor with a door bell.Note:LThe door bell wiring schematic diagram is only an example. Refer to the wiring instructionsprovided with your door bell.Wire type and lengthWiring runWire type *1Diameter Length (Max.)Distribution box –Main monitor0.65 mm 22 AWG approx. 100 m1.2 mm 17 AWG approx. 200 mMain monitor –Power supply unit0.65 mm 22 AWG approx. 10 m2 mm 12 AWG approx. 20 mPower supply unit –AC power source1.2 mm 17 AWGNo requirement2 mm 12 AWGMain monitor –Door bell *20.5 mm - 1.2 mm(24 AWG - 17 AWG)According to specification ofconnected device.*1 Note the following when selecting wiring● Use 2-conductor (solid copper) wiring with a PE (polyethylene)-insulated PVC jacket.Mid-capacitance, non-shielded cable is recommended.● A certified power supply wiring has to be used with this equipment. The relevant nationalinstallation and/or equipment regulations shall be considered. A certified power supplywiring not lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227shall be used.*2 When using a door bell, select a device that meets the following guidelines:● Connection device for option input (A contact) terminal (IN1/IN2):− Input method: No-voltage contact− Open-circuit voltage between terminals: DC 5 V or less− Detection definite time: 0.1 second or more− Short-circuit between terminals: 5 mA or less− Resistance value: make: 500 Ω or less, break: 15 KΩ or more

/ 2

Related manuals for Panasonic VL-MV26