Panasonic VP104W Installation Manual
Precautions for useStandard accessoriesThis system is designed to be used indoors. This product is not operable outdoors.This product has no power switch.When turning off the power, disconnect the power supply from AC adaptor.To keep on using with stable performanceDo not use this camera in hot and humid conditions for a long time. Failure to observe this causescomponent degradation resulting in life shortening of this product.Do not expose this camera to direct heat sources such as a heater.Do not touch the lens with your bare hands.A dirty lens causes deterioration of picture quality.Handle this camera with care.Do not drop this camera, nor apply shock or vibration to this camera. Failure to observe this maycause trouble.About the PC monitorDisplaying the same image on a monitor for a long time may damage the monitor. It is recommend-ed to use a screen-saver.When an error is detected, this product will restart automatically.This product will be inoperable for around 2 minutes after the restart just as when the power isturned on.Product disposal/transferData saved on this product or a storage device used with this product may lead to personalinformation leakage. When it is necessary to dispose or give this product to someone, even whenfor repair, make sure that there is no data on this product.Cleaning this product bodyBe sure to turn off the power before cleaning. Failure to observe this may cause injury. Do not usestrong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration.Transmission intervalImage transmission interval may become slow depending on the network environment,PC performance, shooting subject, access number, etc.About the CMOS image sensorWhen continuously shooting a bright light source such as a spotlight, the color filter of the CMOSimage sensor may have deteriorated and it may cause discoloration. Even when changing the fixedshooting direction after continuously shooting a spotlight for a certain period, the discoloration mayremain.AVC Patent Portfolio LicenseTHIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THEPERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVEREMUNERATION TO(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR(ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONALACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVCVIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONALINFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.SEE HTTP://WWW.MPEGLA.COMFlickeringDue to the influence of lighting, flickering may sometimes happen. Select “Indoor scene(50 Hz)” or“Indoor scene(60 Hz)” in accordance with the power supply frequency in your locality. Refer to theOperating Instructions (included in the CD-ROM) for further information about the setting.Under extremely strong lighting, flickering may happen even when “Indoor scene” is selected for“Light control mode”. When the brightness (illuminance) level on the screen is set to a relatively lowlevel with the [Brightness] buttons, flickering may frequently happen. In such cases, either of the fol-lowing can reduce flickering. Moderate the illumination intensities of objects by changing the camera direction.Set the brightness (illuminance) level on the screen to a brighter level with the [Brightness] but-tons.White-out on images caused by the effect of light control modeWhen “Indoor scene” is selected for “Light control mode”, the tone of the brighter parts on thescreen may be deteriorated than the case when “ELC” is selected.Color blurring on detailed drawing patternsWhen there are detailed drawing patterns on images, color blurring may happen over these parts.Flexible Stand (1 pc.) AC Adaptor (1 pc.) Screw (3 pcs.)(incl. 1 spare)Installation Guide (this document) ........ (1 pc.)Configure the settings of the camera (leaflet) ... (1 pc.)Warranty card (P model) ....................... (1 pc.)CD-ROM*1 ............................................ (1 pc.)*1 The CD-ROM contains the operatinginstructions and different kinds of tool soft-ware programs.Installation GuideNetwork CameraModel No. BL-VP100 SeriesCs0312-0 PGQX1158ZAPrinted in ChinaMain functions● H.264 and JPEG triple encodingA total of 3 outputs, comprising of 2 H.264 outputs and 1 JPEG output, can be provided.● Adaptive darkness correction modeCorrects the blacked-out parts of dark areas of objects that have different illumination intensities.● Wireless LAN function (IEEE802.11 n/g/b) (BL-VP104W/BL-VP104WE/BL-VP104WU)It is possible to monitor camera images and configure camera settings over a wireless network.● WPS (Wi-Fi Protected Setup) function (BL-VP104W/BL-VP104WE/BL-VP104WU)WPS enables the camera to automatically obtain the connection configuration information and thesecurity configuration information of the wireless router. WPS can be configured by pressing theWIRELESS button (WPS button) (PBC method) or entering an 8 digit pin code (Pin code method).Confirm the following items are included in the camera’s packaging.Scanning area: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:3.89 mm (H) x 2.43 mm (V) {5/32 inches (H) x 3/32 inches (V)}VP101/VP101E/VP101U:2.69 mm (H) x 2.02 mm (V) {1/8 inches (H) x 1/16 inches (V)}Scanning system: ProgressiveMinimum illumination: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:Color: 0.9 lx {0.09 footcandle} (F2.8, Auto slow shutter: Off (1/30 s),Gain: On (High))0.06 lx {0.006 footcandle} (F2.8, Auto slow shutter:max. 16/30 s, Gain: On (High))*BW: 0.6 lx {0.06 footcandle} (F2.8, Auto slow shutter: Off (1/30 s),Gain: On (High))0.04 lx {0.004 footcandle} (F2.8, Auto slow shutter:max. 16/30 s, Gain: On (High))*VP101/VP101E/VP101U:Color: 0.9 lx {0.09 footcandle} (F2.8, Auto slow shutter: Off (1/30 s),Gain: On (High))0.11 lx {0.011 footcandle} (F2.8, Auto slow shutter:max. 8/30 s, Gain: On (High))*BW: 0.6 lx {0.06 footcandle} (F2.8, Auto slow shutter: Off (1/30 s),Gain: On (High))0.08 lx {0.008 footcandle} (F2.8, Auto slow shutter:max. 8/30 s, Gain: On (High))** Converted valueGain (AGC): On(Low)/ On(Mid)/ On(High)/ OffAdaptive black stretch: On/OffLight control modesetting:Indoor scene (50 Hz/ 60 Hz)/ ELCELC(Maximum exposure time):VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:ELC(1/30 s), ELC(3/100 s), ELC(3/120 s), ELC(2/100 s), ELC(2/120 s),ELC(1/100 s), ELC(1/120 s), ELC(1/250 s), ELC(1/500 s),ELC(1/1000 s), ELC(1/2000 s), ELC(1/4000 s), ELC(1/10000 s)VP101/VP101E/VP101U:ELC(1/30 s), ELC(3/100 s), ELC(3/120 s), ELC(2/100 s), ELC(2/120 s),ELC(1/100 s), ELC(1/120 s), ELC(1/250 s), ELC(1/500 s),ELC(1/1000 s), ELC(1/2000 s), ELC(1/4000 s), ELC(1/8000 s)Auto slow shutter: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:Off (1/30 s), Max. 2/30 s, Max. 4/30 s, Max. 6/30 s, Max. 10/30 s,Max. 16/30 sVP101/VP101E/VP101U:Off (1/30 s), Max. 2/30 s, Max. 3/30 s, Max. 4/30 s, Max. 8/30 sSimple black & whitemode:Off/AutoWhite balance: ATW1/ ATW2/ AWCDigital noise reduction: High/LowPrivacy zone: On/Off (up to 2 zones available)Camera title on screen: Up to 20 characters (alphanumeric characters, marks), On/OffVideo motion detection(VMD alarm):On/Off (4 areas available)● LensZoom ratio: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:Extra zoom: 1.5x (at VGA resolution)Digital (electronic) zoom: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:4x (Max 6x combined with Extra zoom at VGA)VP101/VP101E/VP101U:4xFocal length: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:3.6 mmVP101/VP101E/VP101U:2.7 mmMaximum aperture ratio: 1 : 2.8Focus range: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:∞ ~ 0.4 mVP101/VP101E/VP101U:∞ ~ 0.5 mAngular field of view: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:Horizontal: 57°, Vertical: 34°VP101/VP101E/VP101U:Horizontal: 53°, Vertical: 40.5°● Wireless (BL-VP104W/BL-VP104WE/BL-VP104WU)Antenna: 1x1 (Diversity)Transmission method: SISO (Single Input/ Single Output) -OFDM, OFDM, DSSSCommunication standard: IEEE802.11n/b/gFrequency range(center frequency)/Channel:VP104W: 2.412 GHz - 2.462 GHz (1 - 11ch)VP104WE/VP104WU: 2.412 GHz - 2.472 GHz (1 - 13ch)Data transfer rate: *1 IEEE802.11n: 6.5 - 72.2 MbpsIEEE802.11g: 6 - 54 MbpsIEEE802.11b: 1 - 11 MbpsAccess method: Infrastructure modeAuthentication method: Open SystemSecurity: *2 WPA/WPA2-PSK (TKIP/AES)WEP (64 bit/128 bit)WPS: PBC method (push button method), PIN method (PIN code method)● NetworkNetwork: 10BASE-T/100BASE-TX, RJ45 connectorDistributing, copying, disassembling, reverse compiling and reverse engineering of the software pro-vided with this product are all expressly prohibited. In addition, exporting any software provided withthis product violating export laws is prohibited.CopyrightAs you will use this unit connected to a network, your attention is called to the following security risks.A Leakage or theft of information through this unitB Use of this unit for illegal operations by persons with malicious intentC Interference with or stoppage of this unit by persons with malicious intentIt is your responsibility to take precautions such as those described below to protect yourselfagainst the above network security risks.Use this unit in a network secured by a firewall, etc.If this unit is connected to a network that includes PCs, make sure that the system is not infect-ed by computer viruses or other malicious entities (using a regularly updated anti-virus program,anti-spyware program, etc.).Protect your network against unauthorized access by restricting users to those who log in withan authorized user name and password.Apply measures such as user authentication to protect your network against leakage or theft ofinformation, including image data, authentication information (user names and passwords), alarmE-mail information, FTP server information and DDNS server information.After the unit is accessed by the administrator, make sure to close the browser.Change the administrator password periodically.Do not install the camera in locations where the camera or the cables can be destroyed or dam-aged by persons with malicious intent.Network securityResolution: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:Imaging mode: 4:3H.264 SVGA (800x600)/ VGA (640x480)/ QVGA (320x240) max.30 fpsJPEG SVGA (800x600)/ VGA (640x480)/ QVGA (320x240) max.30 fpsImaging mode: 16:9H.264 1280x720/ 640x360/ 320x180 max.30 fpsJPEG 1280x720/ 640x360/ 320x180 max.30 fpsVP101/VP101E/VP101U:Aspect ratio: 4:3H.264 VGA (640x480)/ QVGA (320x240) max.30 fpsJPEG VGA (640x480)/ QVGA (320x240) max.30 fpsAspect ratio: 16:9H.264 640x360/ 320x180 max.30 fpsJPEG 640x360/ 320x180 max.30 fpsImage compressionmethod: *3H.264 Image quality: Low/ Normal/ FineTransmission type: Unicast/MulticastBit rate:Constant bit rate/ Best effort:VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/4096 kbps/ 8192 kbpsVP101/VP101E/VP101U:64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/4096 kbpsFrame rate:1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/ 30 fpsJPEG Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/6/ 7/ 8/ 9 LOW (10 steps: 0-9)Transmission type: PULL/PUSHTransmission interval: 0.1 fps - 30 fps (JPEG frame rate will be restricted when displayingboth JPEG and H.264/ images.)Bandwidth control: Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 8192 kbpsProtocol: IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP,SNMP, DHCPv6, MLD, ICMP, ARPIPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP,DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARPOS: *4 *5 Microsoft ® Windows® 7Microsoft® Windows Vista®Microsoft® Windows® XP SP3Browser: Windows® Internet Explorer® 9.0 (32-bit)Windows ® Internet Explorer® 8.0 (32-bit)Windows ® Internet Explorer® 7.0 (32-bit)Microsoft ® Internet Explorer® 6.0 SP3Maximum concurrentaccess number:14 (Depends on network conditions)FTP client: Alarm image transmission, FTP periodic transmissionMulti-screen: Up to 16 camera images can be displayed simultaneously on a multi-screen. (Including the camera itself)Cellular phone compatibility: JPEG imageMobile terminalcompatibility(As of January, 2012): *6iPad, iPhone, iPod touch (iOS 4.2.1 or later)AndroidTM mobile terminals*1 The actual line speed may be different depending on the network environment and the wireless devices connected.*2 Depending on the wireless router (wireless access point) used, connections may not possiblebetween the camera and the wireless router.When connecting with 802.11n, select WPA-PSK (AES) or WPA2-PSK (AES) for security.*3 Transmission for 2 streams can be individually set in the same compression method.*4 For further information about PC system requirements and precautions for when using MicrosoftWindows 7, Microsoft Windows Vista, or Windows Internet Explorer, click “Manual” - “Open” fromthe supplied CD-ROM and refer to “Notes on Windows® / Internet Explorer® versions”.*5 When using IPv6 for communication, use Microsoft Windows 7 or Microsoft Windows Vista.*6 For further information about compatible devices, refer to our website(http://panasonic.net/pss/security/support/info.html).● Optional accessoriesUser License Accessory (For H.264) BB-HCA8A (P model)BB-HCA8CE (E model, U model)Before asking for repairs, check the symptoms with the following table.Contact your dealer if a problem cannot be solved even after checking and trying the solution in thetable or a problem is not described below.Symptom Cause/solutionPower is not turned on. u Is the 6.5 V DC power cable plug (accessory) firmly inserted intothe 6.5 V DC power terminals of the camera? Confirm the power plug is firmly inserted.Be sure to use the power cord plug provided with this prod-uct.TroubleshootingImportant safety instructions1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this apparatus near water.6) Clean only with dry cloth.7) Do not install near any heat sources such as radiators, heat registers, stoves, or other appara-tus (including amplifiers) that produce heat.8) Protect the power cord from being walked on or pinched particularly at plugs, conveniencereceptacles, and the point where they exit from the apparatus.9) Only use attachments/accessories specified by the manufacturer.10) Unplug this apparatus during lightning storms or when unused for long periods of time.11) Refer all servicing to qualified service personnel. Servicing is required when the apparatus hasbeen damaged in any way, such as power-supply cord or plug is damaged, liquid has beenspilled or objects have fallen into the apparatus, the apparatus has been exposed to rain ormoisture, does not operate normally, or has been dropped.Limitation of liabilityTHIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OFTHE THIRD PARTY’S RIGHT.THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICALERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THEIMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).Disclaimer of warrantyIN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANYPERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL,CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENTOPERATION OF THE USER;(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR ORMODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THEMALFUNCTION OR TROUBLE;(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TOANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISINGOUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATIONBEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OFTHAT SURVEILLANCE-CAMERA’S PICTURE, INCLUDING SAVED DATA, FOR SOMEREASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.For U.S. and Canada:Panasonic System CommunicationsCompany of North America,Unit of Panasonic Corporation of North Americawww.panasonic.com/business/For customer support, call 1.800.528.6747Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.Panasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada(905)624-5010www.panasonic.ca© Panasonic System Networks Co., Ltd. 2012For Europe and other countries:http://panasonic.netImporter’s name and address to follow EU rules:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg F.R.GermanyInformation for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying documents meanthat used electrical and electronic products and batteries should not be mixed withgeneral household waste.For proper treatment, recovery and recycling of old products and used batteries,please take them to applicable collection points, in accordance with your national leg-islation and the Directives 2002/96/EC and 2006/66/EC.By disposing of these products and batteries correctly, you will help to save valuableresources and prevent any potential negative effects on human health and the envi-ronment which could otherwise arise from inappropriate waste handling.For more information about collection and recycling of old products and batteries,please contact your local municipality, your waste disposal service or the point of salewhere you purchased the items.Penalties may be applicable for incorrect disposal of this waste, in accordance withnational legislation.For business users in the European UnionIf you wish to discard electrical and electronic equipment, please contact your dealeror supplier for further information.Cd[Information on Disposal in other Countries outside the European Union]These symbols are only valid in the European Union. If you wish to discard these items,please contact your local authorities or dealer and ask for the correct method of disposal.Note for the battery symbol (bottom two symbol examples):This symbol might be used in combination with a chemical symbol. In this case itcomplies with the requirement set by the Directive for the chemical involved.For BL-VP104W/BL-VP104WE/BL-VP104WUOperating near 2.4 GHz electrical appliances may cause interference. Move away from theelectrical appliances.- This equipment must be installed and operated in accordance with provided instructions anda minimum 20 cm {8 inches} spacing must be provided between antenna and all person’sbody (excluding extremities of hands, wrist and feet) during wireless modes of operation.- This transmitter must not be co-located or operated in conjunction with any other antenna ortransmitter.MEDICAL:Consult the manufacturer of any personal medical devices, such as pacemakers, to determine ifthey are adequately shielded from external RF (radio frequency) energy. (The unit operates in thefrequency range of 2.412 GHz - 2.462 GHz (BL-VP104W), 2.412 GHz to 2.472 GHz(BL-VP104WE/BL-VP104WU).) Do not use the unit in health care facilities if any regulationsposted in the area instruct you not to do so. Hospitals or health care facilities may be usingequipment that could be sensitive to external RF (radio frequency) energy.For U.S.AThe model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this unit in the space provided andretain this book as a permanent record of your purchase to aid identification in the event of theft.Model No. _________________________________Serial No. __________________________________For European Union (EU)(BL-VP104E/BL-VP104U/BL-VP101E/BL-VP101U)We declare under our sole responsibility that the product to which this declaration relates is inconformity with the standards or other normative documents following the provisions ofDirectives 2006/95/EC and 2004/108/EC.Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht,mit den folgenden Normen oder normativen Dokumenten übereinstimmt. Gemäß denBestimmungen der Richtlinie 2006/95/EC und 2004/108/EC.Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présentedéclaration est conforme aux normes spécifiées ou à tout autre document normatif conformé-ment aux dispositions des directives 2006/95/CE et 2004/108/CE.Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referenciaesta declaración está conforme con las normas u otros documentos normativos siguiendo lasestipulaciones de las directivas 2006/95/CE y 2004/108/CE.Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presentedichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle dis-posizioni delle direttive 2006/95/CE e 2004/108/CE.Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft,voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepal-ingen van Richtlijnen 2006/95/EC en 2004/108/EC.Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i over-ensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direk-tivene 2006/95/EC og 2004/108/EC.Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är iöverensstämmelse med de standarder eller andra normativa dokument som framställs i direktivnr 2006/95/EC och 2004/108/EC.Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaaseuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 2006/95/EC ja2004/108/EC säädöksiä.Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overens-stemmelse med følgende normer eller andre normgivende dokumenter som følger bestem-melsene i direktivene 2006/95/EC og 2004/108/EC.For European Union (EU) (BL-VP104WE/BL-VP104WU)Panasonic System Networks Co., Ltd., declares that this equipment is in compliance with theessential requirements and other relevant provisions of Radio & Telecommunications TerminalEquipment (R&TTE) Directive 1999/5/EC.Declarations of Conformity for the relevant Panasonic products described in this manual areavailable for download by visiting:http://www.doc.panasonic.deContact:Panasonic Services Europea Division of Panasonic Marketing Europe GmbHPanasonic Testing CentreWinsbergring 15, 22525 Hamgurg, F.R. GermanyAT BE BG CY CZ DKEE FI FR DE GR HUIE IT LV LT LU MTNL PL PT RO SK SIES SE GB IS LI NOCH HR MK TR● BasicPower source: 6.5 V DC (Use only with Panasonic AC adapter)Power consumption: VP104W/VP104WE/VP104WU:max 3.5 WVP104/VP104E/VP104U:max 2.0 WVP101/VP101E/VP101U:max 1.8 WAmbient operating temperature: 0 °C to +40 °C {32 °F to 104 °F}Ambient operating humidity: less than 90 % (No condensation)Dimensions: 70 mm (W) x 70 mm (H) x 25.4 mm (D) {2-3/4 inches (W) x2-3/4 inches (H) x 1 inch (D)} (excluding projection)Mass: VP104W/VP104WE/VP104WU:80 g {0.18 lbs}VP104/VP104E/VP104U/VP101/VP101E/VP101U:75 g {0.17 lbs}Finish: Main body: ABS resin, white● CameraImage sensor: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:1/4 type CMOS image sensorVP101/VP101E/VP101U:1/5 type CMOS image sensorEffective pixels: VP104W/VP104WE/VP104WU/VP104/VP104E/VP104U:Approx. 1 megapixelsVP101/VP101E/VP101U:Approx. 0.32 megapixels(This illustration represents BL-VP104W.)OptionSystem requirements for a PCAbout the user manualsYou will need the following additional items to install and configure the camera.[Locally procured]a PC (used to view settings and images)a router/ a wireless router (when using the wireless function)a LAN cable (CAT-5 straight cable)Refer to “Configure the settings of the camera” (leaflet) for information about the system require-ments for a PC.There are 3 sets of operating instructions for the BL-VP104W, BL-VP104, BL-VP101 (P model),BL-VP104WE, BL-VP104E, BL-VP101E (E model), BL-VP104WU, BL-VP104U, BL-VP101U(U model) as follows.Installation Guide: Explains how to install and connect devices.Configure the settings of the camera: Explains how to connect and configure the network.Operating Instructions (included in the CD-ROM): Explains how to perform the settings and howto operate this camera.Adobe ® Reader® is required to read these operating instructions on the provided CD-ROM.When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from theAdobe web site and install it.“BL-VP104W, BL-VP104, BL-VP101” or “VP104W, VP104, VP101” shown in the instructions andillustrations used in these operating instructions indicates the BL-VP104W, BL-VP104WE,BL-VP104WU, BL-VP104, BL-VP104E, BL-VP104U, BL-VP101, BL-VP101E, BL-VP101U.The screens used in these operating instructions show the cases of P models.PrecautionsWARNINGCAUTIONTurn the power off when cleaning this product.• Failure to observe this may cause injury.Disconnect the AC cord when not using the unit for extended periods of time or• when performing maintenance.Failure to observe this may cause an earth leakage or electric shock.Refer installation work to the dealer.• Installation work requires technique and experiences. Failure to observe this may cause fire,electric shock, injury, or damage to the product.Be sure to consult the dealer.•Stop the operation immediately when something is wrong with this product.• When smoke goes up from the product, the smell of smoke comes from the product, or theexterior of the product has deteriorated, continued use will cause a fire or fall of the productresulting in injury, or damage to the product.Turn the power off immediately and contact qualified service personnel for service.•Select an installation area that can support the total weight.• Selecting an inappropriate installation surface may cause this product to fall down or toppleover, resulting in injury.Installation work shall be started after sufficient reinforcement.•Periodic inspections shall be conducted.• Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.Consult the dealer for the inspections.•Do not install this product in locations subject to vibration.• Loosening of mounting screws or bolts may cause a fall of the product resulting in injury.Make sure that the screws and bolts are tightened firmly.Install this product in a location high enough to avoid people and objects from• bumping the product.Failure to observe this may cause a drop resulting in injury or accidents.Fully insert the AC cord plug into the power outlet.• Do not use damaged plugs or unstable power outlets.Failure to observe this may cause electric shock or heat generation resulting in a fire.When disconnecting or connecting the AC adaptor, do not hold the metal parts• of the plug.Failure to observe this may cause electric shock.Periodically remove dust or other materials from the AC adaptor and its plug part.• Disconnect the AC adaptor and wipe the AC adaptor and its plug part with a dry cloth toremove dust. A fire may be caused if dust or other materials accumulate on the plug part of theAC adaptor and become moist from humidity.Perform all electrical wiring in accordance with the relevant electrical• installation and wiring precautions and regulations.Incorrect electrical wiring may cause fire or electrical shock.Have all electrical wiring perform by a licensed electrician.Do not attempt to disassemble or modify this product.• Failure to observe this may cause fire or electric shock. Consult the dealer for the repair orinspections.Do not insert any foreign objects.• This could permanently damage this product. Turn the power off immediately and contactqualified service personnel for service.Do not use this product in an inflammable atmosphere.• Failure to observe this may cause an explosion resulting in injury.Avoid installing this product in the locations where salt damage occurs or• corrosive gas is produced.Otherwise, the mounting portions will deteriorate and accidents such as a fall of the productmay occur.Use only a dedicated AC cord plug (polarized type).• If other AC cord plugs are used, the voltage and positive/negative polarities may differ and thismay cause fire or electric shock.Do not overload the power outlet or wiring above the specified levels.• Overloading by having many connections on one power outlet may cause heat generationresulting in a fire.Do not damage the AC cord or AC cord plug.• Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable or AC cordplug. Do not place heavy objects on the power cable or AC cord plug. Keep the power cableand AC cord plug away from heat sources. Using a damaged power cable or AC cord plugmay cause electric shock, short circuit, or fire. Consult the dealer for repair.Do not damage internal wiring or plumbing when opening holes in ceiling or• walls for installation or wiring, fixing AC cords, extension cords, or LAN cables,etc. or performing any other installations.Failure to observe this may cause earth leakage, electric shock, or fire.Do not use AC cords from other products.• Failure to observe this may cause fire or electric shock.Do not strike or give a strong shock to this product.• Failure to observe this may cause fire or injury.Do not rub the edges of metal parts with your hand.• Failure to observe this may cause injury.Do not touch this product or the connected cables during thunder (even in the• process of work).Failure to observe this may cause electric shock.Do not insert/remove the AC cord plug with wet hands.• Failure to observe this may cause electric shock.Unplug this unit from power supply if it emits smoke, an abnormal smell or• makes unusual noise, has been dropped or is damaged in any way.These conditions can cause fire or electric shock. Stop using the unit and contact an autho-rized service center.Do not place containers or other objects that contain water or other liquids on• top of the unit.Fire or electrical shock may be caused if water or other liquids enter inside the unit.If water or other liquids enter inside the unit, immediately disconnect the AC cord and contactan authorized service center.Adobe, Acrobat Reader, and Reader are either registered trademarks or trademarks of AdobeSystems Incorporated in the United States and/or other countries.Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registeredtrademarks or trademarks of Microsoft Corporation in the United States and/or other countries.iPad, iPhone, and iPod touch are registered trademarks of Apple Inc., registered in the U.S. andother countries.Android is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.All other trademarks identified herein are the property of their respective owners.Trademarks and registered trademarksSpecificationsWARNING:To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accor-dance with the installation instructions.The mains plug or an appliance coupler shall remain readily operable.The apparatus should not be exposed to dripping or splashing and that no objects filledwith liquids, such as vases, should be placed on the apparatus.For U.S.AThis product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - specialhandling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/For U.S.: BL-VP104WFor U.S. and Canada: BL-VP104, BL-VP101For Europe and other countries: BL-VP104WE, BL-VP104WU, BL-VP104E, BL-VP104U,BL-VP101E, BL-VP101UUL listed model No. BL-VP104W, BL-VP104, BL-VP101For CanadaThis Class B digital apparatus complies with Canadian ICES-003.For U.S.ANOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-tection against harmful interference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the inter-ference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interfer-ence received, including interference that may cause undesired operation.CAUTION:Any changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.Before attempting to connect or operate this product, please read these instructionscarefully and save this manual for future use.The model number is abbreviated in some descriptions in this manual.This manual covers the models: BL-VP100 Series (BL-VP104W, BL-VP104WE,BL-VP104WU, BL-VP104, BL-VP104E, BL-VP104U, BL-VP101, BL-VP101E,BL-VP101U). |
Related manuals for Panasonic VP101
Panasonic BL-VP104W Installation Manual
Panasonic BL-VT164W Installation Manual
Panasonic WV-SP105 Installation Manual
Panasonic BL-C30 Installation Manual
Panasonic WV-SW174W Installation Manual
Panasonic VL-WD812EX Installation Manual
Panasonic WV-NF302 Installation Manual
Panasonic WV-NW960 Installation Manual
Panasonic WV-SW155 Installation Manual
Panasonic WV-NP304 Installation Manual
manualsdatabase
Your AI-powered manual search engine