Panasonic WV-Q168 Operating Instructions Manual

Contents

operating instructions

Panasonic WV-Q168 Operating Instructions Manual Manual pdf 1 page image

Ceiling Mount BracketOperating InstructionsModel No. WV-Q168Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.No model number suffix is shown in this manual.NM0107-0 3TR004927AAA Printed in JapanFeaturesThis ceiling embedded bracket is exclusively designed to mount the Camera, WV-CF284 or WV-CF294, on a ceiling. This ceiling mount bracket is the embedding type so that the camera body willbe dwarfed. This bracket is an embedded type to reduce the exposed portion of the camera body.Precautions• Refer installation work to the dealer.Installation work requires technique and experiences. Failure to observe this may cause fire,electric shock, injury, or damage to the product.• Be sure to consult the dealer.• Use only the specified camera.Failure to observe this may cause a fall of an inappropriate camera resulting in injury or acci-dents.• Mount WV-CF284 or WV-CF294 on this bracket exclusively.• Select an installation area that can support the total weight.If a selected area is too weak to support the total weight, a fall of the product may occur resultingin injury.• Installation work shall be started after sufficient reinforcement.• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas isproduced.Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera mayoccur.• The screws and fixation mechanisms shall be tightened securely.Failure to observe this may cause a fall of the camera resulting in injury.• Periodic inspections shall be conducted.Rust on the metal parts or screws may cause a fall of the product resulting in injury.• Consult the dealer for the inspections.• Do not rub the edges of metal parts with your hand.Failure to observe this may cause injury.• Make sure that the installation area is strong enough to hold the total weight of the cameraassembly (approx. 0.8 kg {1.76 lbs.}) before installation.• The ceiling mount bracket can be installed only when there is a space whose height is 80 mm ormore above a ceiling board.• The ceiling mount bracket can be installed on a ceiling board whose thickness is 30 mm or less.• The camera and the ceiling mount bracket should be fixed using the provided fixing screws, andmake sure that the both of them are fixed firmly.• When the ceiling mount bracket is not necessary anymore, remove from the ceiling.• Avoid installing in the following locations.• Locations where it may get wet from rain or water splash (not only outdoor)• Locations where a chemical agent is used such as a swimming pool• Locations subject to steam and oil smoke such as a kitchen• Locations where radiation or x-ray emissions are produced• Locations where it may be damaged by briny air such as seashores• Locations where the temperature is not within –10 °C to +50 °C {14 °F to 122 °F}.• Locations subject to vibrations (This product is not designed for on-vehicle use.)• Locations where the temperature may rapidly change such as the peripheral areas of the airoutlets of air conditioners or doors facing outside. (In case of installing the camera in suchlocations, the dome cover may become foggy or condensation may be caused on the cover.)• The screws and bolts must be tightened with an appropriate tightening torque according to thematerial and strength of the installation area. After tightening the screws or bolts, perform visualcheck to ensure tightening is enough and there is no backlash.InstallationsBe sure to read "Precautions" before installation. It is recommended to read them while referring theoperating instructions of the camera together.1. Make a hole of 160 mm {6.29"} diameter using a specialized tool, etc.When it is impossible to make a precise holesince no specialized tool is at hand or whenit is impossible to use it because of the loca-tion, trace the hole shape using the provid-ed template.Important:• Make a hole precisely. When the openedhole is bigger or deformed too much, theceiling mount bracket cannot be stuck onthe ceiling board securely.2. Position two of the spring hooks of the camera as shown in the illustration below.When the ceiling mount bracket is installed after positioning them in the opposite side, they maybecome hard to pull out.3. Fix the ceiling mount bracket onto the ceiling board.Loosen the clamping screws until the length between the clamp plates becomes wider that thethickness of the ceiling board, and then clamp the ceiling board by tightening the clampingscrews.Important:• When the ceiling board is the plasterboard, make sure that no crack was made on the ceilingboard by clamping.4. Connect the video cable and the power cord to the camera.Refer to the operating instructions of the camera.5. Fix the camera using four fixing screws(provided).6. Attach the dome cover to the camera andadjust the angular field of view.(Refer to the operating instructions of thecamera.)q Adjust the angular field of view and thefocus.w Attach the dome cover to the camera.e Fix the dome cover using the domecover fixing screw.(To be continued reverse page)Ceiling{6.29"}ø160 mmMain bodySpring hookMove the hook head downward.Main bodyClamp plates* Clamping screw* Tightening torque: 0.61 N·m {6.0 kgf·cm}Triangle markClamp theceiling board.* The "Panasonic" logo on the camera shouldbe located on the side of this triangle mark.Maximum thickness of theceiling board is 30 mm {1.18"}for installation.Main bodyCameraFixing screw(standard accessory)Tightening torque:1.6 N·m {16 kgf·cm}Dome cover fixing screw(provided with the camera)Dome cover

/ 2

Related manuals for Panasonic WV-Q168