Panasonic WV-SUD638 Installation Manual
Also see for WV-SUD638: ManualOperating instructionsImportant informationOperating instructionsManual
Contents |
CameraSun ShadeDummy coveror IR LED unit(optional)Front glassWiperPANrotation partMountingpedestalTilt armTilt lockSide coverWaterproofEXT I/OconnectorWaterproofRJ45connectorWaterproofpower supplyconnectorBottom wiring port Side wiring port*1Mounting pedestalfixing screws ×4(locally procured)Dummy cover or IR LED unit(optional)IMPORTANT:• When the camera is initialized, the settings including the network settings will be initialized. Note that theCRT key (SSL encryption key) used for the HTTPS protocol and the preset entry will not be initialized.• Before initializing the settings, it is recommended to write down the settings in advance.• Do not turn off the power of the camera during the process of initialization. Otherwise, it mayfail to initialize and may cause malfunction.STATUS indicator behaviors• When the power is turned onLights orange → Lights off → Blinks orange → Lights orange (When the network connection is not established)Lights orange → Lights off → Blinks orange → Blinks green → Lights green(When the network connection is established)• During the standby or connectionLights orange (When the cable is not connected)Lights green (When the cable is connected)• During the upgrade processBlinks orange• During the initializationLights orange → Lights off → Blinks orange →Lights orange• Port forwarding error caused by the UPnP functionBlinks orange (in 2 seconds intervals(on for 1 second / off for 1 second))• Trouble happening on the cameraBlinks red• When the installation position is abnormalLights red• This manual describes the installation procedures, network camera installation, cable connec-tions, and adjustment.• Before reading this manual, be sure to read the Important Information (included in the CD-ROM).Parts and functionsStandard accessories Cable preparationImportant safety instructions ......................... 1 pc.Installation Guide (this document) ................. 1 setWarranty card* 1 ............................................ 1 setCD-ROM*2 .................................................... 1 pc.Code label*3.................................................. 1 pc.Attach the provided waterproof connector to the cable to be connected to the camera.* When a conduit is used for wiring, always check its size before installing the waterproof connector.Otherwise, the cable may not be able to pass through the conduit depending on the number of cablesused and the waterproof connector in use.* Always make preparations before the procedure “[3] Attach the waterproof RJ45 connector (acces-sory) to the Ethernet cable.”* Prepare [1] and [2] when necessary.*1 This product comes with several types of warranties. Each warranty is only applicable to the prod-ucts purchased in the regions indicated on the relevant warranty.*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.*3 This label may be required for network management. The network administrator shall retain the code label.Waterproof power supply connector (plug side) ...............................................................................1 setWaterproof EXT I/O connector (plug side) ........................................................................................1 setWaterproof RJ45 connector (plug side) ............................................................................................1 setWasher nozzle mounting bracket A..................................................................................................1 pc.Washer nozzle mounting bracket B..................................................................................................1 pc.Fixing screws for the washer nozzle mounting bracket B ..............................3 pcs. (of them, 1 for spare)Attachment plate .............................................................................................................................1 pc.Fixing screws for attachment plate................................................................. 5 pc. (of them, 1 for spare)Fixing nuts for attachment plate ..................................................................... 5 pc. (of them, 1 for spare)Spring washer ............................................................................................... 5 pc. (of them, 1 for spare)Flat washer .................................................................................................. 10 pc. (of them, 2 for spare)Safety wire.......................................................................................................................................1 pc.Wire clamper ...................................................................................................................................1 pc.Bit (Hex wrench, screw size 6.35 mm {1/4 inches} T20)...................................................................1 pc.Hub/RouterAC100-240 V50/60 HzEthernet cable (category 5e or better, straight)Ethernet cable (category5e or better, straight)PC* 2Tested PoE injector*1Installation procedure• Attach the provided waterproof connector to the cable to be wired to the inside of the ceiling orfloor or along various surfaces, and run the cable through the conduit. (Please choose a conduitof a suitable size to allow the connector to pass through.)Cable preparation• Remove the side cover of the camera so that the wire connection part is visible. (Step.4)• If necessary, install the extension unit (IR LED unit) (optional) if necessary. (Step.5)• If you want to shoot the foot area, bend the tilt arm of the camera forward. (Step.6)• Fix the camera onto the installation location. (Step.8)* Install the washer nozzle mounting bracket pre-fitted with a (recommended) washer nozzle at thesame time.Installation• Connect each waterproof connector to the camera, and fix the side cover back to its original position.Connecting wires(→ Refer to the leaflet “Configuringthe camera so that it can beaccessed from a PC”)• Turn on the power supply, and configure the camera sothat it can be accessed via network.Configuring the camera so that it can be accessed from a PC• About the INITIAL SW (Initial switch)Follow the steps below to initialize the network camera.➀ Cut the power supply to the camera either by unplugging the AC power cord or by turning off thepower supply of the tested PoE injector.➁ Turn on the power of the camera while holding down the INITIAL SW, and keep the INITIAL SW helddown for 10-15 seconds. In about 2 minutes after releasing the INITIAL SW, the camera will start upand the settings, including the network settings, will be initialized.System connection diagramThe camera can be powered by the AC power supply or the tested PoE injector as shown in the follow-ing illustration.*1 For the related information on applicable tested PoE injectors, refer to our website(http://security.panasonic.com/support/info/).*2 Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.*1 The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 orISO 228-1 (parallel pipe threads) G3/4.[1] Attach the waterproof EXT I/O connector (accessory) to the cable* The parts to be used in ➁ and ➂ are in the bag of the waterproof EXT I/O connector (plug side) set. |
Related manuals for Panasonic WV-SUD638
Panasonic WV-SF438 Installation Manual
Panasonic WV-SF138 Installation Manual
Panasonic WV-SF448 Installation Manual
Panasonic WV-SW155 Installation Manual
Panasonic WV-SP509 Installation Manual
Panasonic WV-SW396 Installation Manual
Panasonic WV-SC588 Installation Manual
Panasonic WV-SW352 Installation Manual
Panasonic WV-SW559 Installation Manual
Panasonic WV-SF549 Installation Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine