TMNovember 1996** SPECIAL NOTICE **The ACCULINK CSU has been certified by the Canadian Department ofCommunications to the CS-03 standard. The DOC Certification number is230 5354 A, and the Load number is 6. Please keep this notice with theenclosed documentation.Document No. 3150-A2-GX13-10

Paradyne 3150 Release Note

installation steps

ACCULINK 3150

important safety instructions

reference documents

Overview

Physical Description

Application Example

SNMP or Telnet Connection Examples

Important Instructions

Cabling Examples

Power-Up Self-Test

Operation 3

Using the Front Panel

Displaying Unit Identity

Setting Customer Identification

Changing Configuration Options

Configuring the CSU for SNMP or Telnet Access

setting the ip address

selecting the link layer protocol

specifying the community name(s) and access type(s)

Configuring SNMP Traps

configuring a destination for snmp traps

Establishing Access Security on a Port

Entering a Password to Gain Access

Enabling/Disabling the Front Panel

Using the Integral Modem in Standalone CSUs

disconnecting the modem connection

Enabling the Communication Port for Carrier-Mounted CSUs

Deactivating the Alarm Relay for Carrier-Mounted CSUs

user interface access security for standalone csus

Maintenance 4

Self-Test Health

Device Health and Status

Performance Reports

Alarms

SNMP Traps

Troubleshooting

Test Jacks

Test Commands

Local Loopback Tests

starting a payload loopback

starting a repeater loopback

Test Patterns

Lamp Test

aborting a lamp test

Displaying CSU Test Status

technical specifications

configuration options

configuration worksheets

pin assignments

SNMP MIB Objects E

mib ii (rfc)

interface group, mib ii

ip group, mib ii

tcp group, mib ii

ds1/e1 mib (rfc)

rs-232-like mib (rfc)

generic-interface mib extensions (rfc)

enterprise mib

front panel emulation

starting front panel emulation

menu organization

about this guide

Alarm Message Capability

Standalone CSU Front Panel

Standalone CSU Rear Panel

application example

snmp or telnet connection examples

important instructions

cabling examples

T Front Panel

Keypad

LEDs

displaying led conditions

displaying unit identity

resetting the csu

setting customer identification

changing configuration options

Displaying/Editing Configuration Options

Saving Edit Changes

Setting the 10BaseT Port IP Address

Setting the 10BaseT Port Subnet Mask

Setting the Default Gateway Address

Telnet Access

Selecting the Port

Setting the COM Port or MODEM Port IP Address

Selecting the Link Layer Protocol

Enabling SNMP Trap Messages

Selecting the Number of Trap Managers

Configuring a Destination for SNMP Traps

establishing access security on a port

setting a password

entering a password to gain access

Acquiring the Active User Interface

Releasing the Active User Interface

enabling/disabling the front panel

Changing User Interface Access Security

using the integral modem in standalone csus

entering numbers in the phone directories

initiating a call for front panel pass-through operation

initiating a call for pc, ascii terminal/printer, or snmp operation

self-test health messages

device health and status messages

performance reports

ethernet statistics

snmp traps

troubleshooting

T Test Jacks

Test Jack Configuration (Model 3150)

test commands

local loopback tests

Line Loopback (LLB)

Payload Loopback (PLB)

DTE Loopback (DLB)

Repeater Loopback (RLB)

Aborting Loopbacks

T Test Patterns

Monitoring Test Patterns

Aborting Test Patterns

Starting a Lamp Test

Aborting a Lamp Test

displaying csu test status

T Alarms

T Overview

System Group, MIB II

Interface Group, MIB II

IP Group, MIB II

ICMP Group, MIB II

T DS1/E1 MIB (RFC 1406)

Far End Group, DS1/E1 MIB

General Port Table, RS-232-like MIB

Asynchronous Port Table, RS-232-like MIB

Synchronous Port Table, RS-232-like MIB

T Generic-Interface MIB Extensions (RFC 1229)

T Enterprise MIB

standalone at the central site

local carrier and remote standalone

local and remote carriers – different subnets

local and remote carriers – same subnet

multiple nmss

installing front panel emulation software

Restoring ATI Access

initiating an ati session

ending an ati session

using ati screens

Displaying or Editing Configuration Options

installation procedures

saving edit changes