ACCULINK 3160 AND 3164DSU/CSUQUICK REFERENCEDocument No. 3160-A2-GL11-60

Paradyne 3160 Quick Reference

installation steps

ACCULINK 3160

about this guide

reference documents

DTE Drop/Insert (DSX-1) Interface

SNMP Management Support

Standalone DSU/CSU Rear Panel

application examples

important instructions

Installing the +24 Vdc Power Supply

Installing the Single –48 Vdc Power Supply

Installing the Redundant –48 Vdc Power Supply

cabling examples

T Front Panel

displaying unit identity

displaying led conditions

download operations

setting customer identification

changing configuration options

Displaying/Editing Configuration Options

Saving Edit Changes

Selecting/Copying to a Specific Port

Setting the 10BaseT Port IP Address

Setting the 10BaseT Port Subnet Mask

Setting the Default Gateway Address

Telnet Access

Selecting the Port

Setting the IP Address

Selecting the Link Layer Protocol

Specifying the Community Name(s) and Access Type(s)

Enabling SNMP Trap Messages

Selecting the Number of Trap Managers

Configuring a Destination for SNMP Traps

configuring ds0 channels

Displaying DS0 Channel Assignments

Allocating Data Ports

Block or ACAMI Assignment Method

Individual Channel Assignment Method

to the Network Interface

Clearing DS0 Channel Allocation

providing backup capability

Configuring for Network Timing

Configuring for External Timing

establishing access security on a port

setting a password

entering a password to gain access

Acquiring the Active User Interface

Releasing the Active User Interface

Changing User Interface Access Security

using the integral modem

entering numbers in the phone directories

SNMP Operation

disconnecting the modem connection

performance reports

snmp traps

troubleshooting

test jacks

test commands

Sending a Line Loopback Up or Down

Sending a V.54/ANSI FT1 Activation/Deactivation

local loopback tests

Line Loopback (LLB)

Payload Loopback (PLB)

DTE Loopback (DLB)

Repeater Loopback (RLB)

Data Channel Loopback (DCLB)

Data Terminal Loopback (DTLB)

Aborting Loopbacks

T Test Patterns

Sending Test Patterns

Monitoring Test Patterns

Aborting Test Patterns

Starting a Lamp Test

Aborting a Lamp Test

technical specifications

configuration options

dte interface configuration options

network interface configuration options

general configuration options

T Alarms

configuration worksheets

pin assignments

baset connector

com port interface

power input connector

external clock interface

T Overview

System Group, MIB II

Interface Group, MIB II

IP Group, MIB II

ICMP Group, MIB II

SNMP Group, MIB II

Far End Group, DS1/E1 MIB

DS1 Fractional Group, DS1/E1 MIB

Installing the Single – 48 Vdc Power Supply

Installing the Redundant – 48 Vdc Power Supply

using the front panel

Keypad

Test Jacks

LEDs

Allocating DS0 Channels from the DTE Drop/Insert Interface to the Network Interface

Entering Numbers in the Phone Directories

Initiating a Call for Front Panel Pass-Through Operation

Initiating a Call for PC, ASCII Terminal/Printer, or SNMP Operation

Disconnecting the Modem Connection

device health and status

H Alarms

Starting a Line Loopback

Starting a Payload Loopback

Starting a DTE Loopback

Starting a Repeater Loopback

Starting a Data Channel Loopback

Starting a Data Terminal Loopback

test patterns

H DTE Interface Configuration Options

H Management Configuration Options

aux port interface

General Port Table, RS-232-like MIB

Asynchronous Port Table, RS-232-like MIB

Synchronous Port Table, RS-232-like MIB

Output Signal Table, RS-232-like MIB

Generic Interface Test Table, Generic Interface MIB

front panel emulation

important safety instructions

government requirements and equipment return

Overview

Features

ACCULINK 316x DSU/CSU Physical Description

DSU/CSU Front Panel

DSU/CSU Rear Panel

DSU/CSU Faceplate

Auxiliary Backplane

Planning

Example Point-to-Point Configuration

Multiport T1 DSU/CSU in a Fractional T1 Network Configuration

Serial Connection to SNMP

Box Contents

Optional Power Selection

Vdc Single Source Power Supply Pinouts

Vdc Redundant Source Power Supply Pinouts

Power-Up Self-Test

Selecting a Model 3161 DSU/CSU

Establishing Access Security on a Port

Password Configuration Screen

DSU/CSU Cabling

DSU/CSU Cabling Configurations

Factory Default Configuration Options

Enabling/Disabling the Front Panel

Operation 3

Operating the Front Panel

Model 3161 DSU/CSU Faceplate

System LEDs

NETWORK Interface LEDs

DSX-1 Drop/Insert Port LEDs

Data Port LEDs

displaying led conditions on the front panel

LED Status Screen

LED Display Selection Screen

DSU/CSU Test Jacks

Test Jack Block Diagram

Configuring the DSU/CSU

Configuration Branch for the Front Panel

Configuration Branch for the Async Terminal

Load From Screen

Save Edit Screen

Port Options Configuration Worksheets

SNMP System Options Screen

Edit User Screen

Communication Port Options Screen

specifying the community name(s) and access type(s)

Enterprise-Specific Trap Definitions

Trap Options Screen

Configuring DS0 Channels

Example Channel Allocation

Example Interface Tables

DS0 Channels Containing RBS Information Worksheet

Example Port Channel Configuration Tables (Ports 1 and 2) Worksheet

Example Port Channel Configuration Tables (Ports 3 and 4) Worksheet

Display Channel Symbols

Display Channels Screen

allocating data ports

block channel assignment method example

acami channel assignment method example

DTE Assignment Screen

Timing

configuring for network timing example

Selecting the Shared Communication Port

Checking the Status of the DSU/CSU

Health and Status Messages

displaying device health and status

Self- Test Health Messages

Performance Registers

Carrier (Telco) and User Register Organization

displaying user performance registers

Telco Performance Report Screen

Controlling the DSU/CSU

releasing the active physical interface