Parker Pneumatic MPS-9 Series Installation & Service Instructions Manual
Pneumatic DivisionRichland, Michigan 49083!! WARNINGTo avoid unpredictable system behavior that can cause personal injuryand property damage:• Disconnect electrical supply (when necessary) before installation,servicing, or conversion.• Disconnect air supply and depressurize all air lines connected tothis product before installation, servicing, or conversion.• Operate within the manufacturer’s specified pressure, temperature,and other conditions listed in these instructions.• Medium must be moisture-free if ambient temperature is belowfreezing.• Service according to procedures listed in these instructions.• Installation, service, and conversion of these products must beperformed by knowledgeable personnel who understand howpneumatic products are to be applied.• After installation, servicing, or conversion, air and electricalsupplies (when necessary) should be connected and the producttested for proper function and leakage. If audible leakage is present,or the product does not operate properly, do not put into use.• Warnings and specifications on the product should not be coveredby paint, etc. If masking is not possible, contact your localrepresentative for replacement labels.WARNINGFAILURE OR IMPROPER SELECTION OR IMPROPER USE OFTHE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN ORRELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY ANDPROPERTY DAMAGE.This document and other information from Parker Hannifin Corporation,its subsidiaries and authorized distributors provide product and/orsystem options for further investigation by users having technicalexpertise. It is important that you analyze all aspects of your application,including consequences of any failure and review the informationconcerning the product or systems in the current product catalog. Dueto the variety of operating conditions and applications for these productsor systems, the user, through its own analysis and testing, is solelyresponsible for making the final selection of the products and systemsand assuring that all performance, safety and warning requirementsof the application are met.The products described herein, including without limitation, productfeatures, specifications, designs, availability and pricing, are subjectto change by Parker Hannifin Corporation and its subsidiaries at anytime without notice.EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FORINCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZETHESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.Installation & Service InstructionsCVM-111PMPS-9 Series SensorISSUED: June, 2003Supersedes: July, 2002Doc.# CVM-111P, ECN030385, Rev. 2IntroductionFollow these instructions when installing, operating, orservicing the product.ANSI! CautionsThe MPS-9 Pressure Sensor is designed to monitor pressureand is not a safety measure to prevent accidents.The compatibility of the sensor is the responsibility of the designerof the system and specifications.Operating Environment• Parker / Convum Sensors have not been investigated forexplosion-proof construction in hazardous environments.• Do not use with flammable gases, liquids, or in hazardousenvironments.• Avoid installing the sensor in locations where excessivevoltage surges could damage or affect the performance ofthe sensor.Operations• Dedicate a power supply of 10.8 to 30VDC to the sensorand set the ripple to Vp-p10% or less. Avoid excessivevoltage. Avoid voltage surges.• A small amount of internal voltage drop is possible. Ensurethe power supply minus any internal voltage drop exceedsthe operating load.• Verify the operating media is compatible with the specifiedsensor. Check the chemical make-up, operatingtemperatures, and maximum pressure ranges of the systembefore installing.• Installation of air dryer system is recommended to removemoisture.Installation• Never insert an object into the pressure port other than anappropriate fluid connector.• Avoid short-circuiting the sensor. Connect the brown leadto V+ and blue lead to 0V.• Do not connect the output lead wires (black / white) to thepower supply.• Outputs not being used should be trimmed and insulated.• Install as shown using the metal mounting bracket. |
Related manuals for Parker Pneumatic MPS-9 Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine