Patterson NAC-E Operation Manual
Also see for 043-2005 BB-Y: Operation manual
  |
Cleaning and Drying the ExteriorWash the handpiece under running water following the procedurebelow. (Water condition: ≤100°F, ≥3.5L/min; water should be ofsame quality as drinking water)- Clean the external surfaces ofthe handpiece with a softbristled toothbrush for 15seconds or more.- Clean around the bur insertionhole for 15 seconds or more,using an interdental brush(wire thickness 0.7mm) thatconforms to size 4 in ISO16409.Under appropriate lighting(natural office lighting, 500 lxor higher), inspect thehandpiece for blood or otherdebris. If any visible debris remains, repeat the process until thehandpiece is visually clean.After cleaning, if the residual moisture is present, wipe off withdry cloth or blow it off with compressed air (≤50.75psi) until this no moisture in the interior and exterior.When blowing off with compressed air, cover the handpiece wicloth to prevent scattering of water. Proceed to 6: Cleaning andLubrication.• The Patterson Brand attachment is intended for use by dentalprofessionals only.• Read this operation manual carefully before using the attachment.• Be sure to follow all the operating instructions, including allcautions and warnings.• Keep this Operation Manual for future reference.• Consider primarily the safety of the patient and the operator whenusing the attachment.Caution, before use• Never use non-ISO standard, damaged or worn-out burs.• Use clean burs. Dirt or debris stuck to the bur shank may clogthe chuck mechanism.Caution• Never use the attachment if it cannot be smoothly installedonto or removed from the contra angle sheath. In such a case,consult the Patterson Service Center.Caution1. Specifications- Perform installation/removal of head onto/from the contra anglesheath. Refer to instructions 8: Replacement of Head.2. Installation/Removal of Head onto/from Contra Angle SheathNAC-Y and BB-Y- Swing the latch plate out, holding the sheath connected to the head.- Insert a bur into the chuck hole until the end of the bur touches theback of the chuck.- Swing the latch plate back until it is snaps at the center of thecollar of the contra angle head.- Make sure that the bur is locked securely with the latch, pulling thebur with fingers and rotating it manually.NPB-Y- Holding the sheath connected to the head, press the head buttonwith thumb to open the chuck and then insert a bur into the chuckhole. When the end of the CA bur touches the back of the chuck,release the head button.- Make sure that the bur is securely fixed after the installation,pulling the bur with your fingers and rotating it manually.3. Installation/Removal of bur into/from AttachmentNAC-Y- Setting the motor speed below 30,000rpm, perform a test run ofthe attachment, making sure that the bur is securely installed.- Use the attachment, setting the motor speed appropriately.BB-Y and NPB-Y- Setting the motor speed below 40,000rpm, perform a test run ofthe attachment, making sure that the bur is securely installed.- Use the attachment, setting the motor speed appropriately.4. OperationP/N #sApplicable bursInstallation/removalof burAllowable max. speedApplicable contraangle sheath#043-2005 BB-YISO 2.34 latch burTraditional type40,000rpm#043-3839 NPB-YISO 2.34 latch burPushbutton type40,000rpm#043-4092 NAC-YISO 2.34 latch burTraditional type30,000rpmPAT. #043-4126 ISO E-type, 1:1 drive typePAT. #043-2542 ISO E-type, 4:1 speed reduction typeHEAD: PAT. #043-4092 NAC-YHEAD: PAT. #043-2005 BB-YHEAD: PAT. #043-3839 NPB-YNAC-Y head with E-type Sheath: NAC-E• When abnormal vibration, noise, overheating, etc., occurswhile the attachment is in the test run or in use, stop using theattachment immediately. In such a case, consult thePatterson Service Center.• NAC-Y and BB-Y: Never swing the latch plate out when themotor is rotating.• NPB-Y: Never press pushbutton when the motor is rotating.• Never connect/disconnect the attachment when the motor isrotating.• NAC-Y: Never set motor speed above 30,000rpm.• BB-Y and NPB-Y: Never set motor speed above 40,000rpm.Warning5. Cleaning and DryingCleaning and Lubricating the Interior- Attach an E-Type spraynozzle to the nozzle of thePANA SPRAY Plus.- Shake the can 3 or 4 times,and insert the E-Type spraynozzle into the rear of thehandpiece while holding thehead of the handpiece with a cloth etc.- Hold the handpiece, and spray for 2 or 3 seconds until oil comeout of the handpiece head. Repeat lubrication until foreign matestops coming out of the tip.6. Cleaning and LubricationE-Type spray nozzle: AUTOCLAVABLEOM-CK285E 001OPERATION MANUALLatch Contra Angle AttachmentPAT. #043-2005 BB-YPAT. #043-4092 NAC-YPAT. #043-3839 NPB-YPAT. NAC-ECleaning and Drying the ExteriorWash the handpiece under running water following the proceduresbelow. (Water condition: ≤100°F, ≥3.5L/min; water should be of thesame quality as drinking water)- Clean the external surfaces ofthe handpiece with a softbristled toothbrush for 15seconds or more.- Clean around the bur insertionhole for 15 seconds or more,using an interdental brush(wire thickness 0.7mm) thatconforms to size 4 in ISO16409.Under appropriate lighting(natural office lighting, 500 lxor higher), inspect thehandpiece for blood or otherdebris. If any visible debris remains, repeat the process until thehandpiece is visually clean.After cleaning, if the residual moisture is present, wipe off withdry cloth or blow it off with compressed air (≤50.75psi) until thereis no moisture in the interior and exterior.When blowing off with compressed air, cover the handpiece withcloth to prevent scattering of water. Proceed to 6: Cleaning andLubrication.e Patterson Brand attachment is intended for use by dentalfessionals only.ad this operation manual carefully before using the attachment.sure to follow all the operating instructions, including allutions and warnings.ep this Operation Manual for future reference.nsider primarily the safety of the patient and the operator whening the attachment.Caution, before useever use non-ISO standard, damaged or worn-out burs.se clean burs. Dirt or debris stuck to the bur shank may cloghe chuck mechanism.Cautionever use the attachment if it cannot be smoothly installedonto or removed from the contra angle sheath. In such a case,consult the Patterson Service Center.Cautionpecificationsrform installation/removal of head onto/from the contra angleeath. Refer to instructions 8: Replacement of Head.nstallation/Removal of Head onto/from Contra Angle Sheath-Y and BB-Ying the latch plate out, holding the sheath connected to the head.ert a bur into the chuck hole until the end of the bur touches theck of the chuck.ing the latch plate back until it is snaps at the center of thellar of the contra angle head.ke sure that the bur is locked securely with the latch, pulling ther with fingers and rotating it manually.-Ylding the sheath connected to the head, press the head buttonth thumb to open the chuck and then insert a bur into the chuckle. When the end of the CA bur touches the back of the chuck,ease the head button.ke sure that the bur is securely fixed after the installation,lling the bur with your fingers and rotating it manually.nstallation/Removal of bur into/from AttachmentNAC-Y- Setting the motor speed below 30,000rpm, perform a test run ofthe attachment, making sure that the bur is securely installed.- Use the attachment, setting the motor speed appropriately.BB-Y and NPB-Y- Setting the motor speed below 40,000rpm, perform a test run ofthe attachment, making sure that the bur is securely installed.- Use the attachment, setting the motor speed appropriately.4. Operation#slicable bursllation/removalrwable max. speedlicable contrae sheath#043-2005 BB-YISO 2.34 latch burTraditional type40,000rpm#043-3839 NPB-YISO 2.34 latch burPushbutton type40,000rpm#043-4092 NAC-YISO 2.34 latch burTraditional type30,000rpmPAT. #043-4126 ISO E-type, 1:1 drive typePAT. #043-2542 ISO E-type, 4:1 speed reduction typeHEAD: PAT. #043-4092 NAC-YHEAD: PAT. #043-2005 BB-YHEAD: PAT. #043-3839 NPB-YNAC-Y head with E-type Sheath: NAC-E• When abnormal vibration, noise, overheating, etc., occurswhile the attachment is in the test run or in use, stop using theattachment immediately. In such a case, consult thePatterson Service Center.• NAC-Y and BB-Y: Never swing the latch plate out when themotor is rotating.• NPB-Y: Never press pushbutton when the motor is rotating.• Never connect/disconnect the attachment when the motor isrotating.• NAC-Y: Never set motor speed above 30,000rpm.• BB-Y and NPB-Y: Never set motor speed above 40,000rpm.Warning5. Cleaning and DryingCleaning and Lubricating the Interior- Attach an E-Type spraynozzle to the nozzle of thePANA SPRAY Plus.- Shake the can 3 or 4 times,and insert the E-Type spraynozzle into the rear of thehandpiece while holding thehead of the handpiece with a cloth etc.- Hold the handpiece, and spray for 2 or 3 seconds until oil comesout of the handpiece head. Repeat lubrication until foreign materialstops coming out of the tip.6. Cleaning and LubricationE-Type spray nozzle: AUTOCLAVABLEOM-CK285E 001OPERATION MANUALLatch Contra Angle AttachmentPAT. #043-2005 BB-YPAT. #043-4092 NAC-YPAT. #043-3839 NPB-YPAT. NAC-E |
Related manuals for Patterson 043-2005 BB-Y
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine