Qonnect PL-6N Operating Instructions Manual
  |
OPERATING INSTRUCTIONSHAND TOOL FOR BLIND RIVET NUTS M3-M6AND BLIND RIVET BOLTS M4-M6Manual PL-6NManual PL-6NPL-6NTECHNICAL INFORMATIONCapacity: Blind rivet nuts M3 - M4 - M5 - M6Blind rivet bolts M4 - M5 - M6Material: Aluminium, Steel and Stainless SteelSize: 380 mm (L) x 170 mm (H) 64 mm (P) 16 mm (0Weight: 0.77 KgDESCRIPTION OF THE TOOL1. Tool Body2. Left and right lever3. Turning knob4. Mandrel M65. Anvil M66. Counter lock nut7. Front sleeve with stroke indicator8. Adjust nutRead the manualINSTRUCTIONSThe hand tool will be standard equipped with the M6 anvil and M6mandrel for Rivet nuts.The other components will be stored separate in the carton box.FIRST USE:Make sure before using the tool that the anvil and the mandrel aresuitable for the thread of the insert to be used. Otherwise change it toa different size.CHANGE TO A DIFFERENT SIZE RIVET NUT:Open the levers (2) Now Unscrew the anvil (5) and the lock nut (6). Turn/Pull the turning nob (3) away from the tool. This way it will come loose,and you will be able to withdraw the mandrel from the tool. Replace bychoosing the correct size from the spare parts in the carton box, andre-assemble by following the above steps in the opposite direction.* To change into setting Rivet bolts, choose the correct size Rivboltpuller, and combine it with the correct Anvil and lock nut.A874562 23HLANVIL ADJUSTMENT:After adjusting the stroke, is it necessary to adjust the anvil (5) and itscounter lock nut (6).Open the levers completely. This way the mandrel will come outcompletely. The protrusion of the mandrel out of the anvil should be aslong as the whole rivet nut. This to make sure the full thread of the rivetnut will be used to set the rivet nut. Unscrew the counter lock nut (6)and adjust the anvil (5) by turning left or right, to increase or decreasethe length. After the correct length is applied, screw the counter locknut until it is tight. Changing the threaded inserts or stroke requires thisstep ever time.CSETTING A THREADED INSERT:Put the tool in start position by opening the levers up to a maximum,so that the mandrel will come out completely. Screw the insert on thethreaded end of the mandrel, and make sure it is completely tight. Nowinsert it into the hole of the material. The hole size must be slightlylarger than the rivet nut. Check the specifications of the rivet nut to besure. Close the levers completely to set the rivet nut. Once the rivet nutis set, unscrew the threaded insert by using the turning knob.D6 5STROKE ADJUSTMENT:Close the levers completely and use the adjust nut to increase ordecrease the stroke. The higher the stroke, the higher the deformationof the rivet nut will be, and vice versa.The stroke is dependent on:• The grip range• The blind rivet nutB1pull-link1 04L00438 6 04F60037 11 04L20511 16 04Z20111 21 04L20507 26 04L201292 04P00435 7 04Z20901 12 04L20510 17 04Z20902 22 04L00434 27 04L201283 04L20121 8 04F00102 13 04L20803 18 04L20512 23 04L00436 28 04L207214 04L20122 9 04L21636 14 04L20127 19 04L20513 24 04L00437 29 04L207225 04L20875 10 04L20508 15 04F60166 20 04Z20903 25 04L20130 30 04L207230P |
Related manuals for Qonnect PL-6N
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine