6-68064-01 Rev A, December 2013 *6-68064-01*© 2013 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader,Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliatesin the United States and/or other countries. All other trademarks are the property of their respective owners. Quantumspecifications are subject to change.Quantum Scalar i500:FC I/O Fan Blade ReplacementEach Fibre Channel (FC) I/O blade is cooled by a fan blade. In the Scalar® i500,the fan blade is always installed in the bay to the right of the FC I/O blade. Eachexpansion module has four bays and can accommodate two FC I/O blades andtwo fan blades (see Figure 1 on page 2).

Quantum Scalar i500 Replacement Manual

Purpose

Compatibility Matrix

Resolved Issues

Known Issues

Firmware Versions

Contacting Quantum

Scalar i500

limited warranty

About This Guide and Your Product

Getting More Information or Help

Understanding SMI-S, CIM, and MOF

Your Library, SMI-S, and CIM

Understanding MOF

CIM Profiles and Subprofiles

Storage Library Subprofiles

Element Counting Subprofile

Service Discovery and CIM Indications

Discovering the CIM Server

Using CIM Indications

Web Resources

Resources

Architecture

Requirements

Storage Library Profile Content

Fibre Channel Blade Support

LUN Mapping (EVPS)

quick start guide

Appliance Servers

Installing the SKM Appliance Servers

Configuring the SKM Appliance Servers

Installing and Configuring the SKM VMware Servers

Deploying the .ova Image on VMware

Installing and Configuring the SKM KVM Servers

Deploying the .raw Image on KVM

Configuring the SKM VM Servers on KVM

Installing TLS Certificates on the SKM Server for Pre-SKM 2.4 (240Q)

Requirements for Installing User provided TLS Certificates

Installing TLS Certificates on the SKM Server for SKM 2.4 (240Q) or Later

Executing the Script Without Using the d Option

Generating Quantum Bundles for Certificates

Configuring Your Library For SKM

Configuring the Scalar i2000/i6000 Tape Library

Configuring the Scalar i3/i6 Tape Library

Configuring Multiple Libraries

Backing Up the Servers

fibre channel

Introduction

Step 1: Unpack the Library

Step 2: Install the Library in a Rack (Optional for 5U and 14U)

Step 4: Install the Module Components

Step 5: Connect the Tape Drive Cables

Connecting Fibre Channel Cables Directly to Host or Switch

Connecting Fibre Channel Cables Through a Fibre Channel I/O Blade

Connecting Serial Attached SCSI (SAS) Cables

Step 6: Connect the Library Cables

Step 7: Configure the Library Settings

Step 8: Run the Library

Advanced Reporting Features

Using the Reports and Understanding the Data

Configuring the Drive Resource Utilization Report

Configuring the Media Integrity Analysis Report

Saving and E-mailing Advanced Reporting Data

Deleting Advanced Reporting Data

Description

SNMPv3

SNMP Community Strings

MIB Variables - IPv6 Information

IPv6 Default Hop Limit

IPv6 Interface Description

IPv6 Effective Maximum Transmission Unit

IPv6 Interface Admin Status

MIB Variables - Drive Information

Physical Drive Serial Number

Physical Drive Vendor

Physical Drive Firmware

Physical Drive Library Serial Number

Physical Drive Health Status

Physical Drive Interface Type

Physical Drive SCSI ID

Physical Drive Physical Serial Number

Fibre Channel Port World Wide Node Name

Fibre Channel Port Loop ID Mode

Fibre Channel Port Negotiated Speed

Fibre Channel Port Firmware Revision

Fibre Channel Port Drive Serial Number

Library Interfaces - SAS

SAS Port Negotiated Speed

SAS Port Drive Serial Number

Library Interfaces - SCSI

SCSI Controller Role

SCSI Controller Maximum IDs

SCSI Controller Firmware Revision

SCSI Controller Logical Library Serial Number

MIB Variables - Library System Information

Library SNMP Agent Description

Library Vendor

Library Model

Library URL

Library Firmware Version

Aggregated Main Door Status

Number of Storage Slogs

Number of Physical Drives

Logical Library Name

Logical Library Model

Logical Library Media Domain

Logical Library State

Logical Library Number of I/E Slots

Logical Library Storage Element Address

Logical Library Changer Device Address

Blade Location

Blade World Wide Node Name

Blade Health Check Level

Blade Firmware Revision

Blade EVPS Enabled

Blade State

Blade Host Port Failover Error Recovery Mode

Blade Dev Entry

Blade Device Vendor

Blade Device Serial

Blade Device LUN

Blade Device Firmware Revision

Blade Controller Table

Blade Controller Channel Mask

Blade Fibre Channel Controller Entry

Blade Fibre Channel Controller World Wide Port Name

Blade Fibre Channel Controller Loop ID Mode

Blade Host Table

Blade Host Name

Blade Host Port ID

Blade Host LUN Map

Blade Host Port Failover Map Primary Port

Blade Host Port Failover Map Active Port

Blade Host Port Failover Physical Port Failure Type

MIB Variables - RAS Subsystem

Control Status

Robotics Status

Drive Status

SNMP Traps

Quantum Tape Library MIB

Quantum Library MIB Content

Preface

Chapter 1 Description

Intelligent Storage

Modules

Stackability

Front Panel Components

I/E Station

Front Power Switch

Rear Power Switches

Power System

Library Control Blade

Fibre-Channel Input/Output Blades

Robotic System and Barcode Scanner

Tape Drive Support

Library Features

Control Path Modification

Capacity on Demand (COD)

Quantum Encryption Key Manager (Q-EKM)

Advanced Reporting

Chapter 2 Understanding the User Interface

Common User Interface Elements

System Summary and Subsystem Status

Home

Operator Panel

Menu Trees

User Privileges

User Access

Chapter 3 Configuring Your Library

Using the Default Administrative User Account

Using the Setup Wizard

Default Configuration Settings

Logging On to the Web Client

Modifying Network Settings

Enabling SSL

Configuring SNMP Settings on the Library

Working With Partitions

Automatically Creating Partitions

Manually Creating Partitions

Modifying Partitions

Deleting Partitions

Deleting Partitions Before Removing or Replacing Modules

Changing Partition Access

Disabling/Enabling Manual Cartridge Assignment

Configuring Cleaning Slots

Configuring I/E Station Slots

Configuring Zero I/E Station Slots

Setting Tape Drive Parameters

Working With Control Paths

Adding or Upgrading Licensable Features

About License Keys

Obtaining a License Key

Applying a License Key

Configuring Quantum Encryption Key Manager (Q-EKM)

Step 4: Configure Q-EKM Server TCP/IP Addresses

Step 5: Configure Partition Encryption

Setting Customer Contact Information

Working With E-mail Notifications