M10Quectel Cellular EngineM10 User GuideM10_User_Guide_V1.00 - 1 -

Quectel M10 User Manual

Revision history

Introduction

Terms and abbreviations

Safety caution

Product concept

Functional diagram

Evaluation board

Application interface

Operating modes

Power supply

FIGURE 2: REFERENCE CIRCUIT OF THE VBAT INPUT

Power supply pins

Power up and power down scenarios

FIGURE 6: TURN ON THE MODULE USING KEYSTROKE

Turn off

FIGURE 8: TIMING OF TURN OFF SYSTEM

FIGURE 9: REFERENCE CIRCUIT FOR EMERG_OFF USING DRIVING CIRCUIT

Restart module using the PWRKEY pin

Power saving

SLEEP mode (slow clock mode)

RTC backup

Serial interfaces

TABLE 9: LOGIC LEVELS OF THE SERIAL PORT AND DEBUG PORT

Function of serial port & debug port supporting

Software upgrade and software debug

FIGURE 18: CONNECTION OF SOFTWARE UPGRADE

Audio interfaces

TABLE 11: PIN DEFINITION OF AUDIO INTERFACE

Microphone interfaces configuration

Speaker interface configuration

FIGURE 24: SPEAKER INTERFACE CONFIGURATION OF AOUT2

Earphone interface configuration

Buzzer

SIM card interface

Design considerations for SIM card holder

TABLE 17: PIN DESCRIPTION (AMPHENOL SIM CARD HOLDER)

LCD interface

Keypad interface

FIGURE 32: REFERENCE CIRCUIT OF THE KEYPAD INTERFACE

Behaviors of the RI

Network status indication

General purpose input & output (GPIO)

TABLE 26: PIN DEFINITION OF THE LIGHT_MOS

Antenna interface

Operating frequencies

Electrical, reliability and radio characteristics

TABLE 31: M10 CONNECTION DIAGRAMS

Absolute maximum ratings

Current consumption

Electro-static discharge

Product information

Mechanics

FIGURE 40: PAD BOTTOM DIMENSIONS（UNIT: MM

Footprint of recommendation

FIGURE 41: FOOTPRINT OF RECOMMENDATION（UNIT: MM

Top view of the module

Directives and standards

Safety cautions

Pin description

Monitor power supply

FIGURE 6: TURN ON THE MODULE USING DRIVING CIRCUIT

Power down

FIGURE 10: REFERENCE CIRCUIT FOR EMERG_OFF BY USING DRIVING CIRCUIT

Wake up module from SLEEP mode

FIGURE 14: RTC SUPPLY FROM NON-CHARGEABLE BATTERY

UART Port

FIGURE 18: CONNECTION OF ALL FUNCTIONAL UART PORT

Debug Port

UART Port 3

UART Application

Decrease TDD noise and other noise

Receiver and speaker interface configuration

FIGURE 30: SPEAKER INTERFACE CONFIGURATION OF AOUT2

FIGURE 33: REFERENCE CIRCUIT OF THE 8 PINS SIM CARD

TABLE 15: PIN DESCRIPTION OF AMPHENOL SIM CARD HOLDER

TABLE 18: PIN DEFINITION OF THE ADC

FIGURE 38: RI BEHAVIOUR OF VOICE CALLING AS A RECEIVER

Operating status indication

Open drain output (LIGHT_MOS)

SD card interface

TABLE 26: PIN NAME OF THE SD CARD AND T-FLASH(MICRO SD) CARD

RF output power

FIGURE 47: RECOMMENDATION OF RF PAD WELDING

Power supply ratings

FIGURE 49: M10 BOTTOM DIMENSIONS（UNIT: MM

FIGURE 51: FOOTPRINT OF RECOMMENDATION（UNIT: MM

Bottom view of the module

Appendix A: GPRS coding schemes

Appendix B: GPRS multi-slot classes

Revision History

S parameter syntax

Flow control

Unsolicited Result Code

AT Commands According to V.25TER

Detailed Description of AT Commands According to V.25TER

ATD Mobile Originated Call To Dial A Number

ATD> <n> Originate Call To Phone Number In Current Memory

ATDL Redial Last Telephone Number Used

ATH Disconnect Existing Connection

ATM Set Monitor Speaker Mode

ATO Switch From Command Mode To Data Mode

ATS3 Set Command Line Termination Character

ATS5 Set Command Line Editing Character

Of D Command

ATV TA Response Format

ATX Set CONNECT Result Code Format And Monitor Call Progress

AT&D Set DTR Function Mode

AT&W Store Current Parameter To User Defined Profile

AT+GCAP Request Complete TA Capabilities List

AT+GMI Request Manufacture Identification

AT+GOI Request Global Object Identification

AT+ICF Set TE-TA Control Character Framing

AT+ILRR Set TE-TA Local Data Rate Reporting Mode

AT+IPR Set TE-TA Fixed Local Rate

AT Commands According to GSM07.07

Detailed Descriptions of AT Command According to GSM07.07

AT+CAMM Accumulated Call Meter Maximum (ACM max) Set Or Query

AT+CAOC Advice Of Charge

AT+CCFC Call Forwarding Number And Conditions Control

AT+CCUG Closed User Group Control

AT+CEER Extended Error Report

AT+CGMR Request TA Revision Identification Of Software Release

AT+CSTA Select Type Of Address

AT+CIMI Request International Mobile Subscriber Identity

AT+CKPD Keypad Control

AT+CLCK Facility Lock

AT+CLIP Calling Line Identification Presentation

AT+CLIR Calling Line Identification Restriction

AT+CMEE Report Mobile Equipment Error

AT+COLP Connected Line Identification Presentation

AT+COPS Operator Selection

AT+CPAS Mobile Equipment Activity Status

AT+CPBR Read Current Phonebook Entries

AT+CPBS Select Phonebook Memory Storage

AT+CPBW Write Phonebook Entry

AT+CPIN Enter PIN

AT+CR Service Reporting Control

AT+CREG Network Registration

AT+CRLP Select Radio Link Protocol Parameter

AT+CSQ Signal Quality Report

AT+FCLASS FAX: Select, Read Or Test Service Class

AT+FMM FAX: Rreport Mmodel ID

AT+VTD Tone Duration

AT+CMUX Multiplexer Control

AT+CNUM Subscriber Number

AT+COPN Read Operator Names

AT+CFUN Set Phone Functionality

AT+CSIM Generic SIM Access

AT+CRSL Ringer Sound Levels

AT+CMUT Mute Control

AT+CPUC Price Per Unit And Currency Table

AT+CBC Battery Charge

AT+CUSD Unstructured Supplementary Service Data

AT+CSNS Single Numbering Scheme

AT+CMOD Configure Alternating Mode Calls

AT Commands According to GSM07.05

AT+CMGF Select SMS Message Format

AT+CMGR Read SMS Message

AT+CMGS Send SMS Message

AT+CMGW Write SMS Message To Memory

AT+CMSS Send SMS Message From Storage

AT+CMGC Send SMS Command

AT+CNMI New SMS Message Indications

AT+CPMS Preferred SMS Message Storage

AT+CRES Restore SMS Settings

AT+CSAS Save SMS Settings

AT+CSCB Select Cell Broadcast SMS Messages

AT+CSDH Show SMS Text Mode Parameters

AT+CSMS Select Message Service

AT Commands for GPRS Support

AT+CGDCONT Define PDP Context

AT+CGQMIN Quality Of Service Profile (Minimum Acceptable)

AT+CGQREQ Quality Of Service Profile (Requested)

AT+CGDATA Enter Data State

AT+CGPADDR Show PDP Address

AT+CGEREP Control Unsolicited GPRS Event Reporting

AT+CGREG Network Registration Status

AT+CGSMS Select Service For MO SMS Messages

AT Commands Special for Quectel

Detailed Descriptions of Commands

AT+QPOWD Power Off

AT+QALARM Set Alarm