Quoizel CCR8406K Assembly Instruction Manual

Quoizel CCR8406K Assembly Instruction Manual Manual pdf 1 page image

Package ContentsWarnings and Cautions1of2Assembly Instruction Sheet #IS-CCR8406K _R1For Style CCR8406K2017 QuoizelInc.Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We stronglyrecommend that a licensed, professional electrician perform the installation.Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.A Crossbar Assemblyx 1Please go to for product cleaning tips. Go to the selection.(1) A19 Medium Base bulb 100W Maximum.20-30 minutesIdentify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts arepresent. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacementparts.www.quoizel.com Care + MaintenanceLight Source:Estimated Assembly Time:Preparation:Fixture can only be mounted in the direction indicated on page 2.Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.C Fixture Bodyx 1ReleasedDate:2017-03-13Thank you for purchasing a Quoizel product.Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184or visit us on-line at www.quoizel.comD Glass Panelx 4BAlternateMounting screwx 2STEP 2 Installing the Crossbar Assembly-A. Pass the supply wires through the Crossbar Assembly (A). Attachthe Crossbar Assembly (A) to the Outlet Box with the head of theGreen Ground Screw facing you. Secure the Crossbar Assembly (A)with Outlet Box Screws (not included). Tighten until snugNote: Use the Alternate Shorter Mounting Screw (B) if yourinstallation requires a shorter mounting screw..Supply Wireswith Ground WireOutlet Box Screws(not included)OutletBox AFigure 2Mounting Screwor Alternate ShortMounting ScrewSTEP 3 Test Fit the Backplate to the Crossbar Assembly-A. Remove the mounting balls from the Crossbar Assembly (A). Placethe backplate and Fixture Body (C) onto the Crossbar Assembly (A)and secure with mounting balls. Note: The backplate and FixtureBody (C) should be snug against the wall and held tight with themounting balls. If it is not, adjust the length of the mounting screwor alternate short mounting screw on the Crossbar Assembly (A) byunscrewing the preassembled hex nut and lock washer and thenCMounting BallABackplateHex Nut andLock WasherFigure 3Mounting Screwor Alternate ShortMounting ScrewSTEP 1 - Insert Glass PanelsA. Insert the U-shaped foam end of theGlass Panel (D) into the slot in thebottom of the cage and fasten withthe tabs in the top edge of the cage. TabSlotU-shapedFoamDCFigure 1STEP 4 - Wire ConnectionsA. Use standard wire connectors (not included) to make all wireconnections. Twist connectors until wires are tightly joined together.Wrap each connection with approved electrical tape and carefullystuff all the connected wires into the Outlet Box.Figure 4White wirefrom outlet box White wirefrom fixtureBlack wire fromoutlet box (or Red)Black wirefrom fixtureBare, or GreenGround wirefrom outlet boxGround wirefrom fixtureBare, or GreenGround wirefrom outlet boxORGround wirefrom fixtureGreen Ground Screwon the Crossbarscrewing the mountingscrews or alternate shortmounting screws in or outof the crossbar until thecorrect length isachieved. Once thebackplate and FixtureBody (C) is secure,remove the mounting balland Fixture Body (C) andproceed to Step 4.

/ 2

Related manuals for Quoizel CCR8406K