Quoizel EVG8407EK Assembly Instruction Sheet

Quoizel EVG8407EK Assembly Instruction Sheet Manual pdf 1 page image

Package ContentsWarnings and Cautions1of2Assembly Instruction Sheet #IS-EVG8407EKFor Style EVG8407EK2016 QuoizelInc.Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We stronglyrecommend that a licensed, professional electrician perform the installation.Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.A Crossbar Assemblyx 1CFixtureBodyx 1STEP 1 Install Crossbar Assembly-A. Pass the supply wires through the Crossbar Assembly (A). Attachthe Crossbar Assembly (A) to the Outlet Box with the head of theGreen Ground Screw facing you. Secure it with Outlet Box Screws(not included). Tighten until snug.Note: Use the Alternate Shorter Mounting Screw (B) if yourinstallation requires a shorter mounting screw.Supply Wireswith Ground WireOutlet Box Screws(not included)OutletBoxFigure 1STEP 2 Attach Cage to Fixture Body-A. Place the top edge of the Cage (D)over bolts on the bottom edge of thefixture hood on the Fixture Body (C).Secure by threading Lock Balls (E)onto bolts. Hand tighten until snug.Figure 2APlease go to for product cleaning tips. Go to the selection.(1) A19 Medium Base Bulb 100W Maximum.20-30 minutesIdentify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts arepresent. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacementparts.www.quoizel.com Care + MaintenanceLight Source:Estimated Assembly Time:Preparation:Fixture can only be mounted in the direction indicated on page 2.Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.D Cagex 1E Lock Ballx 2CESTEP 3 Test Fitting Backplateto Crossbar Assembly-A.on Fixture Body(C) to theRemove mounting balls fromthe Crossbar Assembly (A). Fitthe backplateCrossbar Assembly(A) and secure with mountingballs. Note: The backplateshould be snugagainst the wall and themounting balls. IfonFixture Body (C)not, adjust thelength of the mounting screwsor alternate short mountingscrews on the Crossbar Figure 3Mounting BallABackplateHex Nut andLock WasherThank you for purchasing a Quoizel product.Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184or visit us on-line at www.quoizel.com ReleasedDate:2016-08-15BAlternateMounting screwx 2DCAssembly (A) by unscrewing the preassembled hex nut and lockwasher and then screwing the mounting screws or alternate shortmounting screws in or out of the crossbar until the correct length isachieved. Once the backplate on Fixture Body (C) is secure, removethe mounting ball and Fixture Body (C) and proceed to Step 4.Mounting Screwor Alternate ShortMounting ScrewMounting Screwor Alternate ShortMounting ScrewSTEP 4 - Wire ConnectionsA. Use standard wire connectors (not included) to make all wireconnections. Twist connectors until wires are tightly joined together.Wrap each connection with approved electrical tape and carefullystuff all the connected wires into the Outlet Box.White wirefrom supply White wirefrom fixtureBlack wire fromsupply (or Red)Black wirefrom fixtureGround wirefrom supplyGround wirefrom fixtureFigure 4Figure 5STEP 5 Install Fixture Body-A. Carefully tuck all wires into theoutlet box and position thebackplate of Fixture Body (C)over the outlet box. Align theholes in the backplate with themounting screws or alternateshort mounting screws. PlaceMounting BallABackplateCMounting Screwor Alternate ShortMounting Screwcaulk (not supplied) into the previouslyremoved mounting balls and thenattach Fixture using the mountingballs. Hand tighten until snug.

/ 2

Related manuals for Quoizel EVG8407EK