Quoizel RAV8410WT Assembly Instruction Sheet

Quoizel RAV8410WT Assembly Instruction Sheet Manual pdf 1 page image

1of2Assembly Instruction Sheet #IS-RAV8410WTFor Style RAV8410WT2016 QuoizelInc.Thank you for purchasing a Quoizel product.Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184or visit us on-line at www.quoizel.comPackage ContentsDFixture Bodyx 1ACrossbarAssemblyx 1BAlternateMounting screwx 2Please go to for product cleaning tips. Go to the selection.(1) A21 Medium Base Bulb 150W Maximum or(1) S21 Vintage Medium Base 60W Bulb is recommended but not supplied.30-45 minutesIdentify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts arepresent. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacementparts.www.quoizel.com Care + MaintenanceLight Source:Estimated Assembly Time:Preparation:Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.Warnings and CautionsTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We stronglyrecommend that a licensed, professional electrician perform the installation.Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.STEP 3 - Test Fit the Backplate to the Crossbar AssemblyA. Remove the mounting balls from the Crossbar Assembly (A). Placethe backplate and Fixture Body (D) onto the Crossbar Assembly (A)and secure with mounting balls. Note: The backplate and FixtureBody (D) should be snug against the wall and held tight with themounting balls. If it is not, adjust the length of the mounting screwor alternate short mounting screw on the Crossbar Assembly (A) byunscrewing the preassembled hex nut and lock washer and thenscrewing the mounting screws or alternate short mounting screwsin or out of the crossbar until the correct length is achieved. Oncethe backplate and Fixture Body (D) is secure, remove the mountingball and Fixture Body (D) and proceed to Step 4.ReleasedDate:2016-09-26C Fixture Loopx 1STEP 1 Thread Fixture Loop toFixture Body-A. Thread the Fixture Loop (C) onto theFixture Body (D) and hand tightenuntil snug.CDSTEP 2 - Installing the Crossbar AssemblyA. Pass the supply wires through the Crossbar Assembly (A). Attachthe Crossbar Assembly (A) to the Outlet Box with the head of theGreen Ground Screw facing you. Secure the Crossbar Assembly (A)with Outlet Box Screws (not included). Tighten until snugNote: Use the Alternate Shorter Mounting Screw (B) if yourinstallation requires a shorter mounting screw..Figure 2Supply Wires withGround WireOutlet Box Screws(not included)Outlet BoxMounting Screwor Alternate ShortMounting ScrewDMountingBallABackplateHex Nut andLock WasherFigure 3Mounting Screwor Alternate ShortMounting ScrewSTEP 4 - Wire ConnectionsA. Use standard wire connectors (not included) to make all the wireconnections. Twist the connectors until the wires are tightly joinedtogether. Wrap each connection with approved electrical tape andcarefully stuff all the connected wires into the Outlet Box.White wirefrom supply White wirefrom fixtureBlack wire fromsupply (or Red)Black wirefrom fixtureGround wirefrom supplyGround wirefrom fixtureFigure 4

/ 2

Related manuals for Quoizel RAV8410WT