Quoizel RPT8411PN Assembly Instruction Manual

Quoizel RPT8411PN Assembly Instruction Manual Manual pdf 1 page image

Package ContentsWarnings and Cautions1of2Assembly Instruction Sheet #IS-RPT8411PNFor Style RPT8411PN2017 QuoizelInc.Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We stronglyrecommend that a licensed, professional electrician perform the installation.Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.A Crossbar Assemblyx 1Please go to for product cleaning tips. Go to the selection.(1) A21 Medium Base bulb 150W Maximum.20-30 minutesIdentify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts arepresent. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacementparts.www.quoizel.com Care + MaintenanceLight Source:Estimated Assembly Time:Preparation:Fixture can only be mounted in the direction indicated on page 2.Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.C Fixture Bodyx 1ReleasedDate:2017-07-06Thank you for purchasing a Quoizel product.Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184or visit us on-line at www.quoizel.comBAlternateMounting screwx 2GNDFigure 1STEP 1 Remove Styrofoam insideof the Cage-A. Unscrew lock screws on the fixturehood by using screwdrivers andremove the cage from the fixturebody.B. Carefully remove the Styrofoaminside of the cage.LockScrewStyrofoamCageFixture BodySTEP 2 Installing the Crossbar Assembly-A. Pass the supply wires through the Crossbar Assembly (A). Attachthe Crossbar Assembly (A) to the Outlet Box with the head of theGreen Ground Screw facing you. Secure the Crossbar Assembly (A)with Outlet Box Screws (not included). Tighten until snugNote: Use the Alternate Shorter Mounting Screw (B) if yourinstallation requires a shorter mounting screw..Outlet Box Screws(not included)OutletBoxMounting Screwor Alternate ShortMounting ScrewSupply Wireswith Ground WireAFigure 2STEP 3 Test Fit the Backplate to the Crossbar Assembly-A. Remove the mounting balls from the Crossbar Assembly (A). Placethe backplate onto the Crossbar Assembly (A) and secure withmounting balls. Note: The backplate should be snug against the walland held tight with the mounting balls. If it is not, adjust the length ofthe mounting screw or alternate short mounting screw on theCrossbar Assembly (A) by unscrewing the preassembled hex nutand lock washer and then screwing the mounting screws or alternateshort mounting screws in or out of the crossbar until the correctlength is achieved. Once the backplate is secure, remove themounting ball and backplate and proceed to Step 4.Mounting BallABackplateHex Nut andLock WasherMounting Screwor Alternate ShortMounting ScrewSTEP 4 - Wire ConnectionsA. Use standard wire connectors (not included) to make all wireconnections. Twist connectors until wires are tightly joined together.Wrap each connection with approved electrical tape and carefullystuff all the connected wires into the Outlet Box.Figure 4White wirefrom outlet box White wirefrom fixtureBlack wire fromoutlet box (or Red)Black wirefrom fixtureBare, or GreenGround wirefrom outlet boxGround wirefrom fixtureBare, or GreenGround wirefrom outlet boxORGround wirefrom fixtureGreen Ground Screwon the CrossbarFigure 3

/ 2

Related manuals for Quoizel RPT8411PN