Package ContentsWarnings and Cautions1of2Assembly Instruction Sheet #IS-TRE8409KFor Style TRE8409K2016 QuoizelInc.Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We stronglyrecommend that a licensed, professional electrician perform the installation.Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.A Crossbar Assemblyx 1Please go to for product cleaning tips. Go to the selection.(1) A21 Medium Base bulb 150W Maximum.20-30 minutesIdentify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts arepresent. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacementparts.www.quoizel.com Care + MaintenanceLight Source:Estimated Assembly Time:Preparation:Fixture can only be mounted in the direction indicated on page 2.Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.C Fixture Bodyx 1ReleasedDate:2016-11-08Thank you for purchasing a Quoizel product.Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184or visit us on-line at www.quoizel.comD Curve Panelx 2EGlass Panelx 2BAlternateMounting screwx 2FGlassShadex 1GHSteelCollarx 1SocketCollarx 1ISocketCollar Toolx 1STEP 1 Attach the Glass Panels andCurve Panels to Fixture Body-A. Insert one Curve Panel (D) into the cageof the Fixture Body (C). Attach the bottomedge of the Curve Panel (D) to slot on oneside of the cage. And fold the Tabs in thetop edge of the cage to secure the topedge of the Curve Panel (D). Repeat thesame process to install another CurvePanel (D) to another side of the cage.B. Insert one Glass Panel (E) into the cageof the Fixture Body (C). Attach the bottomedge of the Glass Panel (E) to slot in thefront of the cage. And fold the Tabs in thetop edge of the cage to secure the topedge of the Glass Panel (E). Repeat thesame process to install another GlassPanel (E) to the back of the cage.EDSlotTabFigure 1CFGHISocketFigure 2STEP 3 Installing the Crossbar Assembly-A. Pass the supply wires through the Crossbar Assembly (A). Attachthe Crossbar Assembly (A) to the Outlet Box with the head of theGreen Ground Screw facing you. Secure the Crossbar Assembly (A)with Outlet Box Screws (not included). Tighten until snugNote: Use the Alternate Shorter Mounting Screw (B) if yourinstallation requires a shorter mounting screw..Supply Wireswith Ground WireOutlet Box Screws(not included)OutletBox AFigure 3Mounting Screwor Alternate ShortMounting ScrewSTEP 4 Test Fit the Backplate to the Crossbar Assembly-A. Remove the mounting balls from the Crossbar Assembly (A). Placethe backplate and Fixture Body (C) onto the Crossbar Assembly (A)and secure with mounting balls. Note: The backplate and FixtureBody (C) should be snug against the wall and held tight with themounting balls. If it is not, adjust the length of the mounting screw oralternate short mounting screw on the Crossbar Assembly (A) byunscrewing the preassembled hex nut and lock washer and thenscrewing the mounting screws or alternate short mounting screws inor out of the crossbar until the correct length is achieved. Once thebackplate and Fixture Body (C) is secure, remove the mountingSTEP 2 Install Glass Shade-A. Place the Glass Shade (F) and the SteelCollar (G) over the socket as shown. Byusing the Socket Collar Tool (I), thread theSocket Collar (H) onto the socket andhand tighten until snug to secure theGlass Shade (F).